Abstract:The fiber fracture is a very dangerous defect in the aeroengine integral bladed rings which is manufactured by continuous SiC fibers-reinforced titanium alloy matrix composite (Ti-MMC). Currently the lack of an effective method for inspecting the fiber fracture seriously influences the quality control of the aeroengine integral bladed rings, therefore solving the problem of non-destructive testing for deep buried radial micro-cracks is an insurmountable barrier for the application of Ti-MMC integral bladed rings in aviation. In this work, based on the theory of ultrasonic head-waves, the refraction longitudinal waves with the proper angle generated by the creeping wave probe are propagated on the interface, which means the creeping wave with high energy is generated. The finite element simulation model of the creeping wave is established for inspecting the defect of SiC fibers breakage in Ti-MMC aero-engine bling structure. Based on the results of the finite element simulation, significant defect signal waves are generated in the water layer above the defect. After that, not only the ultrasonic propagation characteristics at the interface of multilayer media but also the diffraction phenomenon of the creeping wave when they encounter the broken wire defect are analyzed. And the detection signal amplitude is not only affected by the incident angle of the creeping probe but also is related to the thickness of titanium alloy. In order to receive the diffracted waves with high sensitivity, the assembled probe, which is composed by a creeping wave exciter (5 MHz, 20 degrees) and an immersion focusing sensor (5 MHz, diameter 6 mm), is specially designed and manufactured according to the results of the finite element simulation. In addition, the artificial sample with the broken fiber is prepared and then tested by the ultrasonic C-scan testing system with the assembled probe. The results show that the three-layer broken wire defects (the crack height is about 0.42 mm) with different depths in the artificial sample can be detected successfully. The C-scan results can match the defect positions of the artificial sample which means this detection method is valid. This method is simple, economical and fast, and is expected to solve the problem of nondestructive testing for broken wire in the deep embedded fiber ring in the Ti-MMC aero-engine bling structure.

Ultrasonic TFM Inspection and Quantitative Method of Defects for Curved Surface Structures of Aeroengine Casing Rings

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Ultrasonic TFM imaging inspection of large complex rings using defect quantitative evaluation mappings

Scattering of Torsional Flexural Guided Waves from Circular Holes and Crack-Like Defects in Hollow Cylinders

TFM Imaging of Aeroengine Casing Ring Forgings with Curved Surfaces Using Acoustic Field Threshold Segmentation and Vector Coherence Factor

Research of Ultrasonic Inspection for Complex Form Aircraft Forging Component

Ultrasonic Detection Method of Micro Defects in Thick-Section CFRP

Simulation on qualitative detection of defects with multi-mode total focusing method

Characterization of internal defects in cylindrical components using laser ultrasonic method with a modified SAFT algorithm

Finite element based research on ultrasonic spectral characteristic of inner wall defect of metal materials

Quantitative Detection of Shallow Subsurface Defects by Using Mode-Converted Waves in Time-of-Flight Diffraction Technique

Ultrasonic Phased Array Inspection of Aeroengine Casing Ring Forgings Using Adaptive Filtering and Angle Gain Compensation Algorithm

Visualizing Defects of Irregular Weld Seams Based on MultiMode TFM Detection

Quantitative Detection of Surface Defect Using Laser-Generated Rayleigh Wave with Broadband Local Wavenumber Estimation

Finite Element Analysis of Defect Detection in Curved Pipes Using Ultrasonic Guided Waves

Ultrasonic inspection of curved structures with a hemispherical-omnidirectional ultrasonic probe via linear scan SAFT imaging

Laser Ultrasonic High Precision Imaging Method for Internal Defects of Small-Diameter Cylindrical Components

Ultrasonic Detection for Fiber Broken in Aero-Engine Integral Bladed Ring

Ultrasonic full-matrix imaging of curved-surface components

Ultrasonic Nondestructive Testing and Evaluating System for the Brazing Quality of a Guide Ring

Quantitative Ultrasonic Testing for Near-Surface Defects of Large Ring Forgings Using Feature Extraction and GA-SVM