Abstract:The successive approximation register (SAR) ADC is the most energy efficient architecture with moderate conversion rate and resolution. However, its comparator noise limits its resolution without sacrificing power efficiency. The delta-sigma modulator (DSM) is the most popular architecture for achieving high SNDR due to its oversampling, but the bulky operational amplifier (op-amp) makes it area inefficient. In LTE Advanced, the bandwidth (BW) of downlink ADCs needs to be configured according to the number of inter-band non-contiguous carrier aggregation (NCCA), which motivates us to combine the benefits of both architectures to reduce area and power consumption simultaneously with high SNDR. The noise-shaping SAR ADC [1] suppresses the comparison and quantization noise in signal BW using a simple cascaded FIR-IIR filter, which obviates the need for a power-hungry low-noise comparator or high-performance op-amp. To some extent, the noise-shaping SAR ADC is a hybrid of DSM and SAR ADCs. Hence, it has the potential to achieve the high resolution and good power efficiency of DSM and SAR ADCs, respectively. However, the passive sampling in an FIR filter introduces considerable thermal noise to the ADC, making it difficult to achieve a high SNR. This work presents an energy-efficient noise-shaping SAR ADC that uses a gain-enhanced dynamic amplifier and some capacitors to construct a low-noise dynamic FIR-IIR filter. The prototype achieves a peak SNDR of 79.74dB over a 5MHz BW with a power consumption of 0.46mW from a 1V supply.

A Fully-Dynamic Kt/c-Noise-canceled SAR ADC with Trimming-Free Dynamic Amplifier.

A SAR ADC with Reduced kT/C Noise by Decoupling Noise PSD and BW

An 18-Bit 2MSPS SAR ADC with Double Passive Noise-Shaping Calibration

A 16-Bit 2.5-Ms/s SAR ADC with On-Chip Foreground Calibration

A 93.6Db-Sndr 5Khz-Bw Fully Dynamic Hybrid CT-DT Noise Shaping SAR ADC

A 0.004mm2 200MS/S Pipelined SAR ADC with Kt/c Noise Cancellation and Robust Ring-Amp

A 13-Bit 0.005-Mm2 40-Ms/s SAR ADC with Kt/c Noise Cancellation

A 0.004-Mm2 200-Ms/s Pipelined SAR ADC with Kt/c Noise Cancellation and Robust Ring-Amp

A Fully Dynamic Low-Power Wideband Time-Interleaved Noise-Shaping SAR ADC

16.5 A 13b 0.005mm<sup>2</sup> 40MS/s SAR ADC with kT/C Noise Cancellation

16.5 A 13b 0.005mm(2) 40ms/S Sar Adc With Kt/C Noise Cancellation

A 13.5-ENOB, 107-μW Noise-Shaping SAR ADC With PVT-Robust Closed-Loop Dynamic Amplifier

A 93.6-Db SNDR Fully Dynamic CT–DT Noise-Shaping SAR ADC with Closed-Loop Capacitively Coupled Two-Stage FIA

A 348-Μw 68.8-Db SNDR 20-Ms/s Pipelined SAR ADC with a Closed-Loop Two-Stage Dynamic Amplifier

9.5 A 13.5B-Enob Second-Order Noise-Shaping SAR with PVT-Robust Closed-Loop Dynamic Amplifier

28.1 A 0.46mW 5MHz-BW 79.7dB-SNDR noise-shaping SAR ADC with dynamic-amplifier-based FIR-IIR filter

A Low Power Noise-Shaping SAR ADC with Improved Integrator and Hybrid DAC Mismatch Mitigation Technique

A Second-Order Noise-Shaping SAR ADC with Passive Integrator and Tri-Level Voting

A 800 MS/s, 12-Bit, Ringamp-Based SAR Assisted Pipeline ADC with Gain Error Cancellation

A 1.5-MHz BW 81.2-dB SNDR Dual-Residue Pipeline ADC With a Fully Dynamic Noise-Shaping Interpolating-SAR ADC

A Fully-Dynamic Time-Interleaved Noise-Shaping SAR ADC Based on CIFF Architecture.