Abstract:Titanium aluminide (TiAl) alloys are promising high-temperature structural materials in the aerospace field. Additive manufacturing is a desirable process for fabricating TiAl alloys. In the process of wire arc additive manufacturing of TiAl alloys, Al-based and Ti-based wires were used as the feedstocks. However, it is hard to ensure the two different wires melt synchronously under the heat of one single arc, so the desired microstructures with gamma (TiAl) phase and alpha(2) (Ti3Al) phase are hard to obtain. A two-wire TOP-TIG-based additive manufacturing process for TiAl alloys is proposed in this paper. The Ti6Al4V wire and pure Al wire are used as the feedstocks. The Al wire is fed in TOP-TIG mode behind the molten pool, while the Ti6Al4V wire is fed in conventional TIG mode in front of the molten pool. The two wires melt synchronously in a broad range of parameters. The compositions of the component can be controlled by adjusting the two-wire feeding speeds. The main microstructures of the as-fabricated component contain alpha(2)/gamma lamellae colonies, equiaxed gamma grains, and alpha(2) grains. In the top and middle regions, when the Al content is 45 at.%, the structures are full alpha(2)/gamma lamellae; as the Al content increases to 50 at.%, some equiaxed gamma grains distribute at the grain boundaries; the component with 55 at.% Al content exhibits the structures consists of equiaxed gamma grains with snowflake-shaped alpha(2)/gamma lamellae colonies. In the bottom region, all components exhibit the coarse equiaxed alpha(2) grains with gamma laths. As the Al content increases, the alpha(2) phase decreases, but the gamma phase increases, and from the top region to the bottom region, the volume fraction of the alpha(2) increases by about 19.4 %. The hardness value of the top and bottom regions is higher, and the middle region exhibits the lowest hardness. As the Al content increases, the hardness decreases. The component with 50 at.% Al exhibits the highest compressive strength with 1762 MPa and the largest compressive ratio with 26.1%.

Wire-based Directed Energy Deposition of a Novel High-Performance Titanium Fiber-Reinforced Al5183 Aluminum Alloy

Twin-wire Directed Energy Deposition-Arc of Ti–48Al–2Cr–2Nb Alloy: Feasibility, Microstructure, and Tensile Property Investigation

Microstructure Modification of Twin-Wire Directed Energy Deposition-Arc Fabricated Γ-Tial Alloy Via Deposition Current Control

Modification of Microstructure and Mechanical Properties for Twin-Wire Directed Energy Deposition-Arc Fabricated Ti-48al-2cr-2nb Alloys Via Current Regulation

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Fatigue Performance of Titanium–Aluminum–Vanadium Alloy Fabricated by Laser-Wire-Based Directed Energy Deposition Forming Dot-Shaped Beads

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Effect of In-Situ Generated Fe3AlC0.5 on the Microstructure and Mechanical Property of Twin-Wire Directed Energy Deposition-Arc Fabricated Fe3Al Based Iron Aluminide

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Wire-Arc Directed Energy Deposition of Aluminum Alloy 7075 with Dispersed Nanoparticles

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

Superior High-Cycle Fatigue Property Through In-Situ Precipitation of Α' Martensite in Additively Repaired Titanium Alloy

Fatigue Performance of Ti-6Al-4V Processed by Wire-Arc Directed Energy Deposition

Fabrication of Fe–30Al alloy using plasma arc welding powered twin-wire directed energy deposition-arc process: Droplet transfer, microstructure, and mechanical property investigation

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

Nanoscale Engineering of Low-Misfit TiB2/Al3(Sc,Zr)/α-Al Multi-Interface to Improve Strength-Ductility Synergy for Direct Energy Deposited Aluminum Alloy

Influence of Tungsten Addition on Microstructure and Tensile Properties of Ti6Al4V Fabricated by Laser-Directed Energy Deposition

Fabrication of Titanium Aluminide Alloys by Twin-Wire Tungsten Inert Gas Welding Applied with High-Frequency Induction Heating Wire Technology: Processing, Microstructure, and Properties

Wire Arc Additive Manufacturing of Titanium Aluminide Alloys Using Two-Wire TOP-TIG Welding: Processing, Microstructures, and Mechanical Properties