Abstract:Photoelectrochemical water splitting using semiconductor materials is one of the most promising methods for converting solar energy into chemical energy. Among the commonly used semiconductors, p-type CuBi2O4 is considered one of the most suitable photocathode materials and can allow a theoretical photocurrent density of about 20 mA center dot cm(-2) for photoelectrochemical water splitting. However, due to severe charge carrier recombination, the obtained photocurrent density is much lower than the theoretical value. Highly efficient photoelectrochemical performance relies on fast charge carrier separation and transport, and prompt reaction kinetics. In this study, we report the development of a polyoxometalate-modified CuBi2O4/Mg- CuBi2O4 homojunction photocathode to improve both the bulk and interfacial charge carrier transport in the photocathode. For the bulk of the photocathode, the built-in electric field originating from the CuBi2O4/Mg-CuBi2O4 homojunction promotes the migration of photo-excited electrons on the conduction band from pure CuBi2O4 to Mg-doped CuBi2O4. Additionally, the electric field facilitates the transfer of holes from the valence band of Mg-doped CuBi2O4 to pure CuBi2O4. This directional transfer of both photo-excited electrons and holes plays a significant role in promoting separation and suppressing the recombination of the charge carriers. On the surface of the photocathode, the reduced polyoxometalate co-catalyst Ag6[P2W18O62] (AgP2W18) was used as a proton sponge to accelerate surface reaction kinetics and suppress carrier recombination. These synergistic effects improved the photo-generated charge carrier transfer and reaction kinetics. As a result, the novel photocathode displayed excellent photoelectrochemical properties, and the photocurrent density was observed to be-0.64 mA center dot cm(-2) at 0.3 V vs. RHE, which is better than that of-0.39 mA center dot cm(-2) for a pure photocathode. Furthermore, the novel photocathode had an applied bias photon-to-current efficiency (ABPE) higher than 0.19% at 0.3 V vs. RHE. In contrast, the pure photocathode had an ABPE of similar to 0.12% under the same conditions. Additionally, when H2O2 was used as an electron scavenger, the photocurrent density was-3 mA center dot cm(-2) at 0.3 V vs. RHE, which is an improvement of approximately 1.5 times compared to the pure photocathode. Furthermore, the charge separation and charge injection efficiency of the novel photocathode were significantly improved compared with the pure photocathode. The experimental results conclusively indicate that the formation of the CuBi2O4/Mg-CuBi2O4 homojunction and AgP2W18 modification played a significant role in the improved performance of the CuBi2O4 photocathode. The performance of the novel photocathode was comparable with the results reported in previous studies, demonstrating its promising potential in real applications.

Thin-layer Metal Bismuth Inserted into Bi2S3/C, N Co-Doped Α-Fe2o3 Achieving Efficient Photoelectrochemical Water Oxidation

Ultrathin NiMn-layered Double Hydroxide Nanosheets Coupled with Α-Fe2o3 Nanorod Arrays for Photoelectrochemical Water Splitting

High-performance bismuth vanadate photoanodes cocatalyzed with nitrogen, sulphur co-doped ferrocobalt-metal organic frameworks thin layer for photoelectrochemical water splitting

A novel α-Fe2O3 photoanode with multilayered In2O3/Co–Mn nanostructure for efficient photoelectrochemical water splitting

Synergy of Ultrathin CoOx Overlayer and Nickel Single Atoms on Hematite Nanorods for Efficient Photo‐Electrochemical Water Splitting

n‐ZrS3/p‐ZrOS Photoanodes with NiOOH/FeOOH Oxygen Evolution Catalysts for Photoelectrochemical Water Oxidation

In Situ Synthesis of Ti:Fe2O3/Cu2O P-N Junction for Highly Efficient Photogenerated Carriers Separation

A Ternary Nanostructured Α-Fe2o3/au/tio2 Photoanode with Reconstructed Interfaces for Efficient Photoelectrocatalytic Water Splitting

Interface And Surface Engineering Of Hematite Photoanode For Efficient Solar Water Oxidation

Facile Synthesis of a Micro–Nano-Structured FeOOH/BiVO4/WO3 Photoanode with Enhanced Photoelectrochemical Performance

Co-optimization of CuBi2O4 photocathode by heterojunction and hole-selective layer for efficient photoelectrochemical water splitting

Criss-crossed α-Fe2O3 nanorods/Bi2S3 heterojunction for enhanced photoelectrochemical water splitting

Heterojunction and co-catalyst engineering of bismuth vanadate by nickel molybdenum oxide and carbon quantum dot decorations for photoelectrochemical water splitting

Fe‐N Co‐Doped BiVO4 Photoanode with Record Photocurrent for Water Oxidation

An Iron Oxide -Copper Bismuth Oxide Photoelectrochemical Cell for Spontaneous Water Splitting

Strongly Coupled Metal Oxide/Reassembled Carbon Nitride/Co-Pi Heterostructures for Efficient Photoelectrochemical Water Splitting

Improved Photoelectrochemical Performance by Polyoxometalate-Modified CuBi2O4/Mg-CuBi2O4 Homojunction Photocathode

A N-Si/coox/ni:Coooh Photoanode Producing 600 Mv Photovoltage for Efficient Photoelectrochemical Water Splitting

An Interface‐cascading Silicon Photoanode with Strengthened Built‐in Electric Field and Enriched Surface Oxygen Vacancies for Efficient Photoelectrochemical Water Splitting

Promoting the Photoelectrochemical Properties of BiVO4 Photoanode via Dual Modification with CdS Nanoparticles and NiFe-LDH Nanosheets

Α-Fe2o3/ag/cds Ternary Heterojunction Photoanode for Efficient Solar Water Oxidation