Abstract:Dissimilar metal welds (DMWs) between high-Cr martensitic heat-resistant steels and nickel-based alloys with nickel-based filler metals are widely used in fossil-fired power plants. Reports of premature failures of DMW joints have attracted considerable attention as such occurrences in the field can lead to significant economic loss and safety issues. Moreover, a comprehensive understanding of the high-temperature performance of new types of DMWs is lacking. In this work, creep tests were conducted over a stress range of 140-260 MPa at of 600 and 620 'C. A shift in the fracture location with variations in stress was observed, with three typical failure modes. At high stress levels (240-260 MPa), the DMW fractured in the base metal (BM) of martensitic steel, accompanied by a large degree of plastic deformation. At intermediate stress levels (200-240 MPa), the DMW fractured in the fine-grained heat-affected zone (FGHAZ) and the inter-critical heat-affected zone (ICHAZ), with creep cavities around coarsened carbides, indicating a typical type IV crack. At low stress levels (140-200 MPa), the DMW fractured in a mixed mode involving three stages. First, a crack initiated at the interface between the nickel-based weld metal and the martensitic steel, which was attributed to the interaction between the oxidation behavior of the martensitic steels and the thermal stress arising from the mismatch in the coefficients of thermal expansion. Second, the crack deflected into the FGHAZ/ICHAZ and developed into a type IV crack mode. Finally, the crack propagated into the adjacent BM, featuring significant plastic deformation. In addition, in the stress-LMP (Larson-Miller parameter) plot, the creep life at a relatively low stress level was shorter than that predicted by linear extrapolation of the data obtained at a high stress level, indicating a premature failure tendency at low stress. This premature failure tendency can be attributed to microstructure degradation in HAZs and preferential oxidation at the interface at low stress levels.

Effect of Residual Stress Introduced by Local Loading on Fracture Behaviour of DMWJ under Different Constraints

Fracture Behavior of DMWJ Under Different Constraints Considering Residual Stress

Effect of Residual Stress Induced by Different Cooling Methods in Heat Treatment on the Fatigue Crack Propagation Behaviour of GH4169 Disc

An Experimental Investigation of In-Plane Constraint Effect on Local Fracture Resistance of A Dissimilar Metal Welded Joint

In-situ observations on local fracture behavior in a dissimilar metal weld joint of nuclear power plant

Local fracture behavior in an Alloy 52M dissimilar metal welded joint in nuclear power plants

An experimental investigation of local fracture resistance and crack growth paths in a dissimilar metal welded joint

Out-of-plane Constraint Effect on Local Fracture Resistance of a Dissimilar Metal Welded Joint

Local fracture properties and dissimilar weld integrity in nuclear power systems

Numerical Investigation of Ductile Crack Growth Behavior in a Dissimilar Metal Welded Joint

Constraint-Dependent J-R Curves of A Dissimilar Metal Welded Joint for Connecting Pipe-Nozzle of Nuclear Pressure Vessel

Local fracture properties and dissimilar weld integrity in nuclear power plants

Experimental Characterisation and Numerical Modelling of Residual Stresses in a Nuclear Safe-End Dissimilar Metal Weld Joint

Analysis of Crack Propagation Behaviors in RPV Dissimilar Metal Welded Joints Affected by Residual Stress

Numerical Analysis of Constraint and Strength Mismatch Effects on Local Fracture Resistance of Bimetallic Joints

Effect of Inhomogeneous Mechanical Properties on the Stress-Strain Field at the Crack Tip and Crack Growth Direction in Dissimilar Metal Welded Joints

Geometry and Material Unified Constraint-Dependent J-R Curves of a Dissimilar Metal Welded Joint

Effect of Loading Mode on Fracture Behavior of CrNiMoV Steel Welded Joint in Simulated Environment of Low Pressure Nuclear Steam Turbine

Evolution of in-plane stresses induced fracture behaviors of Tailor Welded Blanks subjected to non-uniformly distributed load

Residual stress effects on short crack propagation behavior in friction stir welded 7075-T6 aluminum alloy panel under biaxial loading: An experimental and numerical study

Fracture Location Shift of Dissimilar Metal Welds under Coupled Thermal-Stress Effect