Abstract:The mechanical properties of dissimilar metal-welded joint materials are heterogeneous, which is an obstacle to the safety evaluation of key welded structures. The variation of stress–strain conditions at the crack tip caused by mismatch of material mechanical properties in dissimilar metal-welded joints is an important factor affecting crack propagation behavior. To understand the influence of uneven distribution of ultimate strength of the base metal and the welded metal on the crack propagation path, fracture toughness, as well as the mechanical field at the crack tip in the small-scale yield range, the user-defined field variable subroutine method is used to express continuous variation characteristics of welded joint ultimate strength in finite element software. In addition, the J-integral during crack propagation is calculated, and the effect of the ultimate strength on the J-integral and the stress field at the crack tip are analyzed. The results show that as the crack propagation direction is perpendicular to the direction of ultimate strength, the gradient of ultimate strength increases from |Gy|= 50 to |Gy|= 100 MPa/mm, the crack deflection angle increases by 0.018%, and the crack length increases by 1.46%. The fracture toughness of the material decreased slightly during crack propagation. Under the condition that the crack propagation direction is the same as the direction of ultimate strength, the crack propagation path is a straight line. As the gradient of ultimate strength increases from Gx = 50 to Gx = 100 MPa/mm, the crack propagation length decreases by 5.17%, and the slope of fracture toughness curve increases by 51.63%. On the contrary, as the crack propagates to the low ultimate strength side, the crack propagation resistance decreases, the ultimate strength gradient increases from Gx = −100 to Gx = −50 MPa/mm, and the slope of the fracture toughness curve decreases by 51.01%. It is suggested to consider the relationship between crack growth behavior and ultimate strength when designing and evaluating the structural integrity of cracks at the material interface of dissimilar metal-welded joints.

Geometry and Material Unified Constraint-Dependent J-R Curves of a Dissimilar Metal Welded Joint

Experimental study of the static behavior of tubular N-joints

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Research On Safety Assessment Method For Pressure Pipe With Incomplete Welding Defects Under Complicated Loadings

Quantification of the Complex Crack Geometry Effect on Fracture Resistance Using Strain-Based Finite Element Damage Analysis

Calculation and Discussion for Crack Driving Force of Dissimilar Metal Welded Joint of Nuclear Power Equipment Nozzle and Safe End

Investigation of the applicability and effectiveness of unified constraint parameters on A516 Gr70 steel specimens under ductile fracture

Data-driven probabilistic failure assessment curve based on similitude principle

Effect of Inhomogeneous Mechanical Properties on the Stress-Strain Field at the Crack Tip and Crack Growth Direction in Dissimilar Metal Welded Joints

Characterizations of Material Constraint Effect for Creep Crack in Center Weldment under Biaxial Loading

Stress–strain curves of metallic materials and post‐necking strain hardening characterization: A review

Characterization of creep constraint effect for brazed joint specimens at crack tip by new constraint parameter A

Development of J-Integral Solutions for Semi-Elliptical Circumferential Cracked Pipes Subjected to Internal Pressure and Bending Moment

Numerical Investigation of the Influence of Ultimate-Strength Heterogeneity on Crack Propagation and Fracture Toughness in Welded Joints

Numerical simulation of weld fracture using cohesive interface for novel inter-module connections

A comparative study of three forms of an uncoupled damage model as fracture judgment for thin-walled metal sheets

Test-and-FE-based method for obtaining complete stress-strain curves of structural steels including fracture

Experimental and Fea Investigations on the Fracture Properties of Pipe Structures under Internal Pressure in Dbtt Region

Investigation on Fatigue Behaviour of Load-Carrying Fillet Welded Joints Based on Mix-Mode Crack Propagation Analysis

Quantification of crack tip constraint effect based on the critical distance