Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Host‐Guest Strategy Enabling Nonhalogenated Solvent Processing for High‐Performance All‐Polymer Hosted Solar Cells†

Host‐Guest Active Layer Enabling Annealing‐Free, Nonhalogenated Green Solvent Processing for High‐Performance Organic Solar Cells

Guest electron-accepting polymer doping enables green solvent-processed all-polymer solar cells with 16.37% efficiency

A guest-assisted molecular-organization approach for >17% efficiency organic solar cells using environmentally friendly solvents

Green‐Solvent‐Processed 17% Efficient Polymer Solar Cell Achieved Synergistically by Aligning Energy Levels and Improving Morphology with the Quaternary Strategy

Layer‐by‐Layer‐Processed Ternary All‐polymer Organic Solar Cells with 17.74% Efficiency Enabled by introducing a designed narrow‐bandgap guest polymer acceptor

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

18.1% Ternary All‐Polymer Solar Cells Sequentially Processed from Hydrocarbon Solvent with Enhanced Stability

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

Achieving highly efficient all-polymer solar cells by green-solvent-processing under ambient atmosphere

19.5% Efficiency organic solar cells enabled by a direct C–H arylation-derived wide-bandgap small-molecule guest donor

Manipulating Molecular Organization in High-Efficiency Organic Solar Cells

Highly Efficient All‐Polymer Solar Cells Processed from Nonhalogenated Solvents

Improving Efficiency of Non-Fullerene Polymer Solar Cells by Using Non-Halogenated Solvents

Synergic Interface Optimization with Green Solvent Engineering in Mixed Perovskite Solar Cells

Improved photovoltaic performance and robustness of all-polymer solar cells enabled by a polyfullerene guest acceptor

Non-halogenated Solvents for Environmentally Friendly Processing of High-Performance Bulk-Heterojunction Polymer Solar Cells

Synchronously regulating the alkyl side-chain and regioisomer of polymerized small molecule acceptor enabling highly efficient all-polymer solar cells processed with non-halogenated solvent

Enhancing Performances of Solution-Processed Inverted Ternary Small-Molecule Organic Solar Cells: Manipulating the Host-Guest Donors and Acceptor Interaction

Optimization Of Processing Solvent And Film Morphology To Achieve Efficient Non-Fullerene Polymer Solar Cells Processed In Air