Abstract:In this work, thioacetamide (TA) is selected as a sulfur‐containing additive for the precursor solution used in the hydrothermal deposition of Sb2(S,Se)3. With the incorporation of TA, the formation of large voids within the Sb2(S,Se)3 absorber is suppressed, and deep‐level donor‐like defects such as sulfur vacancies are passivated, resulting in enhanced performance of Sb2(S,Se)3 solar cells. Antimony selenosulfide (Sb2(S,Se)3) has recently emerged as a promising light‐absorbing material, attributed to its tunable photovoltaic properties, low toxicity, and robust environmental stability. However, despite these advantages, the current record efficiency for Sb2(S,Se)3 solar cells significantly lags behind their Shockley–Queisser limit, especially when compared to other well‐established chalcogenide‐based thin‐film solar cells, such as CdTe and Cu(In,Ga)Se2. This underperformance primarily arises from the formation of unfavorable defects, predominately located at deep energy levels, which act as recombination centers, thereby limiting the potential for performance enhancement in Sb2(S,Se)3 solar cells. Specifically, deep‐level defects, such as sulfur vacancy (VS), have a lower formation energy, leading to severe non‐radiative recombination and compromising device performance. To address this challenge, thioacetamide (TA), a sulfur‐containing additive is introduced, into the precursor solution for the hydrothermal deposition of Sb2(S,Se)3. This results indicate that the incorporation of TA helps in passivating deep‐level defects such as sulfur vacancies and in suppressing the formation of large voids within the Sb2(S,Se)3 absorber. Consequently, Sb2(S,Se)3 solar cells, with reduced carrier recombination and improved film quality, achieved a power conversion efficiency of 9.04%, with notable improvements in open‐circuit voltage and fill factor. This work provides deeper insights into the passivation of deep‐level donor‐like VS defects through the incorporation of a sulfur‐containing additive, highlighting pathways to enhance the photovoltaic performance of Sb2(S,Se)3 solar cells.

A Robust Hydrothermal Sulfuration Strategy toward Effective Defect Passivation Enabling 6.92% Efficiency Sb<sub>2</sub>S<sub>3</sub> Solar Cells

Efficient In Situ Sulfuration Process in Hydrothermally Deposited Sb2S3 Absorber Layers

Bulk Defect Passivation for Full‐Inorganic Sb2S3 Solar Cells by Sulfur‐Atmosphere Recrystallization Process

8.2%-Efficiency Hydrothermal Sb2S3 Thin Film Solar Cells by Two-Step RTP Annealing Strategy

Innovative In Situ Passivation Strategy for High‐Efficiency Sb2(S,Se)3 Solar Cells

A Novel Multi‐sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%‐efficiency Sb2S3 Planar Solar Cells

Engineering the charge extraction and trap states of Sb 2 S 3 solar cells

Enhanced Hydrothermal Heterogeneous Deposition with Surfactant Additives for Efficient Sb2S3 Solar Cells

A Novel Multi-Sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%-Efficiency Sb2 S3 Planar Solar Cells.

Additive‐Assisted Hydrothermal Growth Enabling Defect Passivation and Void Remedy in Antimony Selenosulfide Solar Cells

Confined‐Space Selenium‐Assisted Tellurization Posttreatment Strategy for Efficient Full‐Inorganic Sb2S3 Thin‐Film Solar Cells

Mechanistic Study of the Transition from Antimony Oxide to Antimony Sulfide in the Hydrothermal Process to Obtain Highly Efficient Solar Cells.

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Negative-pressure Sulfurization of Antimony Sulfide Thin Films for Generating a Record Open-Circuit Voltage of 805 Mv in Solar Cell Applications

Crystal Reconstruction and Defect Healing Enabled High-Quality Sb2Se3 Films for Solar Cell Applications

Crystal Growth Promotion and Defect Passivation by Hydrothermal and Selenized Deposition for Substrate-Structured Antimony Selenosulfide Solar Cells

Confined‐space selenium assisted tellurization post‐treatment strategy for efficient full‐inorganic Sb2S3 thin film solar cells

Surface Treatment Processed Electron Transport Layers for Efficient Sb2S3 Solar Cells

Heterogeneous Nucleation Regulation Amends Unfavorable Crystallization Orientation and Defect Features of Antimony Selenosulfide Film for High‐Efficient Planar Solar Cells

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Recent Advances and Prospects of Solution-Processed Efficient Sb<sub>2</sub>S<sub>3</sub> Solar Cells