Abstract:In this work, thioacetamide (TA) is selected as a sulfur‐containing additive for the precursor solution used in the hydrothermal deposition of Sb2(S,Se)3. With the incorporation of TA, the formation of large voids within the Sb2(S,Se)3 absorber is suppressed, and deep‐level donor‐like defects such as sulfur vacancies are passivated, resulting in enhanced performance of Sb2(S,Se)3 solar cells. Antimony selenosulfide (Sb2(S,Se)3) has recently emerged as a promising light‐absorbing material, attributed to its tunable photovoltaic properties, low toxicity, and robust environmental stability. However, despite these advantages, the current record efficiency for Sb2(S,Se)3 solar cells significantly lags behind their Shockley–Queisser limit, especially when compared to other well‐established chalcogenide‐based thin‐film solar cells, such as CdTe and Cu(In,Ga)Se2. This underperformance primarily arises from the formation of unfavorable defects, predominately located at deep energy levels, which act as recombination centers, thereby limiting the potential for performance enhancement in Sb2(S,Se)3 solar cells. Specifically, deep‐level defects, such as sulfur vacancy (VS), have a lower formation energy, leading to severe non‐radiative recombination and compromising device performance. To address this challenge, thioacetamide (TA), a sulfur‐containing additive is introduced, into the precursor solution for the hydrothermal deposition of Sb2(S,Se)3. This results indicate that the incorporation of TA helps in passivating deep‐level defects such as sulfur vacancies and in suppressing the formation of large voids within the Sb2(S,Se)3 absorber. Consequently, Sb2(S,Se)3 solar cells, with reduced carrier recombination and improved film quality, achieved a power conversion efficiency of 9.04%, with notable improvements in open‐circuit voltage and fill factor. This work provides deeper insights into the passivation of deep‐level donor‐like VS defects through the incorporation of a sulfur‐containing additive, highlighting pathways to enhance the photovoltaic performance of Sb2(S,Se)3 solar cells.

Efficient In Situ Sulfuration Process in Hydrothermally Deposited Sb2S3 Absorber Layers

A Novel Multi‐sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%‐efficiency Sb2S3 Planar Solar Cells

A Novel Multi-Sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%-Efficiency Sb2 S3 Planar Solar Cells.

8.2%-Efficiency Hydrothermal Sb2S3 Thin Film Solar Cells by Two-Step RTP Annealing Strategy

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Enhanced Performance of Close-Spaced Sublimation Processed Antimony Sulfide Solar Cells via Seed-Mediated Growth

Precursor Engineering of Solution‐Processed Sb 2 S 3 Solar Cells

Efficient CdS/Sb 2 S 3 interfacial modification using sodium borohydride etching for enhanced performance of low-cost full-inorganic antimony-based solar cells

Zn(O,S) Buffer Layer for in Situ Hydrothermal Sb 2 S 3 Planar Solar Cells

Engineering the charge extraction and trap states of Sb 2 S 3 solar cells

Additive‐Assisted Hydrothermal Growth Enabling Defect Passivation and Void Remedy in Antimony Selenosulfide Solar Cells

Crystal Growth Promotion and Defect Passivation by Hydrothermal and Selenized Deposition for Substrate-Structured Antimony Selenosulfide Solar Cells

Efficient planar antimony sulfide thin film photovoltaics with large grain and preferential growth

Aqueous-Solution-Based Approach Towards Carbon-Free Sb2 S3 Films for High Efficiency Solar Cells.

Self‐Regulated Growth of Large‐Grain Sb2S3 Thin Films for High‐Efficiency Solar Cells

Efficiency improvement for post-sulfurized CIGS solar cells enabled by in situ Na doping

Heterogeneous Nucleation Regulation Amends Unfavorable Crystallization Orientation and Defect Features of Antimony Selenosulfide Film for High‐Efficient Planar Solar Cells

Confined‐space selenium assisted tellurization post‐treatment strategy for efficient full‐inorganic Sb2S3 thin film solar cells

Innovative In Situ Passivation Strategy for High‐Efficiency Sb2(S,Se)3 Solar Cells