Abstract:Abstract Tribocorrosion is a failure phenomenon which involves synergistic effect of electrochemical corrosion and mechanical wear. It usually results into early failure of mechanical components than simple wear and corrosion. Chloride (Cl − ) and sulfate ions SO 4 2 − are often found together in corrosive media. In this study, the synergistic effect of Cl − and SO 4 2 − on tribocorrosion of 316L stainless steel was studied by changing the ratio of SO 4 2 − /Cl − in corrosive solution from 0.31 M : 0 to 0 : 0.62 M. The stainless steel was worn against with a ZrO 2 sphere. The coefficient of friction (COF), material loss volume, surface micro-topographies and surface chemical composition in different solutions were compared to explore the synergism between SO 4 2 − and Cl − . The results indicated that the mix of Cl − and SO 4 2 − reduced material loss volume by a quarter when compared with that in pure Na 2 SO 4 or NaCl solution. More than half of material loss was caused by the synergism between wear and corrosion in mixing solutions. The synergistic effect between SO 4 2 − and Cl − could promote the transmission of metal into oxides. This had two effects on tribocorrosion. First, the existence of oxides would cause abrasion which accelerated wear-affected corrosion and enhanced mechanical wear (corrosion-affected wear). On the other side, the transmission of metal into oxides benefited for the formation of tribo-film. The flexible stainless steel needed to coordinate deformation with the tribo-film which had relatively low deformability. This aggravated deformation of stainless steel and promoted surface work-hardening effect. It was helpful for stainless steel to resist wear, thus, the corrosion-affected wear was decreased.

Crevice Corrosion Behaviors of Alloy 690 and 405 Stainless Steel in Chloride Solutions with Different Concentrations of Thiosulfate

Effects of Thiosulfate and Dissolved Oxygen on Crevice Corrosion of Alloy 690 in High-Temperature Chloride Solution

Crevice Corrosion Behavior of Alloy 690 in High-Temperature Aerated Chloride Solution

Nodular corrosion inside the crevice of Alloy 690 in deaerated high-temperature chloride solution

Insight into the crevice corrosion mechanism of AA7075‐T651 high‐strength aluminum alloys in neutral nitrate solution: The effect of Cl−

In Situ Electrochemical Monitoring of the Crevice Corrosion Process of the 7075-T651 Aluminium Alloy in Acidic NaCl and NaNO3 Solution

Crevice Corrosion Performance of 436 Ferritic Stainless Steel Studied by Different Electrochemical Techniques in Sodium Chloride Solutions with Sulfate Addition

Effect of Temperature, Chloride Ion and Ph on the Crevice Corrosion Behavior of SAF 2205 Duplex Stainless Steel in Chloride Solutions

Accelerating Effect and Critical Ph Value of Occluded Cell Corrosion Within Pits, Crevices, or Stress Corrosion Cracks

Insights into the Stress Corrosion Cracking Propagation Behavior of Alloy 690 and 316 L Stainless Steel in KOH Versus LiOH Oxygenated Water

Numerical Study on the Crevice Corrosion of 304 Stainless Steel

Corrosion Behavior of Alloy 690 in Aerated Supercritical Water

Stress corrosion crack initiation in Alloy 690 in high temperature water

Study on the roles of bisulfite in the stress corrosion cracking of 7050-T7451 aluminum alloy in the thin electrolyte layer environment

A high-resolution characterization of surface film formed on alloys 800 and 690 exposed to chloride and thiosulfate-containing solution at 300°C

The stress corrosion cracking behavior of N80 carbon steel under a crevice in an acidic solution containing different concentrations of NaCl

Corrosion Behavior of 6061 Aluminum Alloy in Simulated SO2-Polluted Seawater

Corrosion of Aluminum Alloy Metal Matrix Composites in Neutral Chloride Solutions

CORROSION BEHAVIOR OF NUCLEAR GRADE ALLOYS 690 AND 800 IN SIMULATED HIGH TEMPERATURE AND HIGH PRESSURE PRIMARY WATER OF PRESSURIZED WATER REACTOR

Tribocorrosion investigation of 316L stainless steel: the synergistic effect between chloride ion and sulfate ion

Corrosion Behavior of Alloy 22 According to Hydrogen Sulfide, Chloride, and pH in an Anaerobic Environment