Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Limiting Phase Separation Via Halogen-Free Solvent Slot-Die Processing Enables Highly Efficient and Eco-Friendly All-Polymer Solar Cells

Hot Hydrocarbon‐Solvent Slot‐Die Coating Enables High‐Efficiency Organic Solar Cells with Temperature‐Dependent Aggregation Behavior

Kinetic Processes of Phase Separation and Aggregation Behaviors in Slot-die Processed High Efficiency Y6-based Organic Solar Cells

Morphology Evolution in High‐Performance Polymer Solar Cells Processed from Nonhalogenated Solvent

Flow-enhanced Solution Printing of All-Polymer Solar Cells

Optimizing Domain Size and Phase Purity in All-Polymer Solar Cells by Solution Ordered Aggregation and Confinement Effect of the Acceptor

All-Polymer Solar Cells Employing Non-Halogenated Solvent and Additive

Slot-die coated large-area flexible all-polymer solar cells by non-halogenated solvent

Dissolution Swelling Effect-Assisted Interfacial Morphology Refinement Enables High Efficiency All-Polymer Solar Cells

Vertical Composition Distribution and Crystallinity Regulations Enable High-Performance Polymer Solar Cells with >17% Efficiency

Non-halogenated Solvents for Environmentally Friendly Processing of High-Performance Bulk-Heterojunction Polymer Solar Cells

All-Polymer Solar Cells Sequentially Solution Processed from Hydrocarbon Solvent with a Thick Active Layer

High-efficiency Organic Solar Cells Processed from a Halogen-Free Solvent System

Enabling High Efficiency of Hydrocarbon‐Solvent Processed Organic Solar Cells through Balanced Charge Generation and Non‐Radiative Loss

Random Copolymerization Strategy for Non-Halogenated Solvent-Processed All-Polymer Solar Cells with a High Efficiency of over 17%

A Top‐Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All‐Polymer Solar Cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Achieving highly efficient all-polymer solar cells by green-solvent-processing under ambient atmosphere

In Situ Structure Characterization in Slot‐Die‐Printed All‐Polymer Solar Cells with Efficiency over 9%

Optimization Of Processing Solvent And Film Morphology To Achieve Efficient Non-Fullerene Polymer Solar Cells Processed In Air

Morphology Control Realizes Fast Charge Dissociation and Transport in High-Performance All-Polymer Solar Cells