Abstract:For traditional spent fuel shielding materials, due to physical and chemical defects and cost constraints, they have been unable to meet the needs. Therefore, this paper carries out the first discussion on the application and performance of bismuth in neutron shielding by establishing Monte Carlo simulation on the neutron flux model of shielded spent fuel. Firstly, functional fillers such as bismuth oxide, lead oxide, boron oxide, gadolinium oxide and tungsten oxide are added to the matrix to compare the shielding rates of aluminum alloy matrix and silicone rubber matrix. The shielding rate of silicone rubber mixture is higher than aluminum alloy mixture, reaching more than 56%. The optimal addition proportion of bismuth oxide and lead oxide is 30%, and the neutron radiation protection efficiency reaches 60%. Then, the mass attenuation coefficients of bismuth oxide, lead oxide, boron oxide, gadolinium oxide and tungsten oxide in silicone rubber matrix are simulated with the change of functional fillers proportion and neutron energy. This simulation result shows that the mixture with functional fillers has good shielding performance for low energy neutrons, but poor shielding effect for high energy neutrons. Finally, in order to further evaluate the possibility of replacing lead oxide with bismuth oxide as shielding material, the half-value layers and various properties of bismuth oxide and lead oxide are compared. The results show that the shielding properties of bismuth oxide and lead oxide are basically the same, and the mechanical properties, heat resistance, radiation resistance and environmental protection of bismuth oxide are better than that of lead oxide. Therefore, in the case of neutron source strengths in the range of 0.01–6 MeV and secondary gamma rays produced below 2.5 MeV, bismuth can replace lead in neutron shielding applications.

Beryllium Oxide Utilized in Nuclear Reactors: Part II, A Systematic Review of the Neutron Irradiation Effects

Beryllium Oxide Utilized in Nuclear Reactors: Part I: Application History, Thermal Properties, Mechanical Properties, Corrosion Behavior and Fabrication Methods

Molecular Dynamics Study of the Irradiation Damage Accumulation in Beryllium Oxide at Different Temperatures

Stress Corrosion Phenomenon of BeO at Room Temperature and Its Mechanism: Experimental and molecular dynamics study

Blistering Behavior of Beryllium and Beryllium Alloy under High-Dose Helium Ion Irradiation

Effect of low-temperature neutron irradiation on the properties of titanium beryllide

Response of 11 B Enriched ZrB 2 Ultra-High Temperature Ceramic to Neutron Irradiation at Elevated Temperatures

Hot-pressing of BeO Ceramics and Its Thermal Conductivity and Flexural Strength

Radioactive study of oxidation-corrosion materials activated by neutron in lead-bismuth eutectic reactors

Radiation Effects in Novel Nuclear Materials

Changing Mechanisms of High-Temperature Oxidation of Zr-1%Nb Alloy in Air and Steam by Surface Modification with Charged Particles

Study on the shielding performance of bismuth oxide as a spent fuel dry storage container based on Monte Carlo simulation

Radiation damage of MoAlB at elevated temperatures: Investigating MAB phases as potential neutron shielding materials

Effects of Gamma Irradiation on Functional Response of Relaxor-Ferroelectric Thin Films

Atom probe tomography characterization of high-dose ion irradiated MA957

Oxygen Vacancies and Local Amorphization Introduced by High Fluence Neutron Irradiation in Β -Ga2o3 Power Diodes

Helium irradiation effects on MgO-Nd2Zr2O7 composite ceramics prepared by one-step method used for inert matrix fuel

A Brief Review of the Impact of Neutron Irradiation Damage in Tungsten and Its Alloys

Preparation, Deformation Behavior and Irradiation Damage of Refractory Metal Single Crystals for Nuclear Applications: A Review

Reactor Performance and Safety Characteristics of Beryllium-Based Composite Moderators as Replacements for Graphite in mHTGRs

Molecular Dynamics Simulation of High Temperature Mechanical Properties of Nano-Polycrystalline Beryllium Oxide and Relevant Experimental Verification