Abstract:In this study, Mg–5Li–3Al–2Zn alloy was successfully fabricated by melting and casting followed by hot extrusion at 573 K. The initial extruded Mg–5Li–3Al–2Zn alloy presented a bimodal structure in which both coarse grains and fine grains coexisted. The asymmetry of tension and compression, texture evolution and twinning types in extruded Mg–5Li–3Al–2Zn alloy during axial tensile and compressive deformations were studied. The experimental results showed that the initial texture component of the extruded Mg–5Li–3Al–2Zn alloy was {0001} basal texture, which led to a strong yield asymmetry of tension and compression (TYS/CYS of 1.46). When the alloy was stretched along the axis, the texture changed little. The main deformation was (101¯0) prismatic slip with few {101¯2} extension twins produced in some coarse grains, which resulted in weak strain hardening. When the compression was along the axial direction, the initial stage of compressive deformation was dominated by (0001) basal slip. With the increase in strain, large numbers of {101¯2} extension twins and few {101¯2}-{101¯2} double twins were generated in coarse grains. On the other hand, (0001) planes of some fine grains began to rotate and became perpendicular to ED, resulting in the formation of a weak {1¯21¯0}<101¯0> texture. With further increase in strain, {0001} basal texture was completely transformed into {1¯21¯0} <101¯0> texture. Furthermore, based on theoretical analysis, the extruded Mg–5Li–3Al–2Zn alloy had lower CRSS of prismatic and basal slips compared to other Mg alloys.

Achieving Improved/Reversed Tension–Compression Asymmetry by Tailoring Extrusion Processing for Mg–Sn(–Y) Alloy

The Improved Tension-Compression Asymmetry with Double-Extrusion for Mg-Sn-(Y) Alloys

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Improving Tension/Compression Asymmetry of a Hot‐Extruded Mg–Zn–Y–Zr Alloy Via Yttrium Addition

Improved Tension/compression Asymmetry Achieved in High-Strength Magnesium Alloys Via Compression-Extrusion Process

Influencing Factors and Controlling Methods of Tension-Compression Asymmetry in Magnesium Alloys

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

Reducing Yield Asymmetry in a Wrought Mg–9Al Alloy by Randomized Texture Achieved Via Multi-Directional Forging

Adjusting Approaches of Basal Texture for Improvement of Tension-Compression Asymmetry in Extruded Magnesium Alloys

Improving the tension-compression asymmetry of ZK61 magnesium alloy through texture optimization in combined extrusion

Tension-compression Asymmetry of a Rolled Mg-Y-Nd Alloy

Fabrication of Mg/Mg Composite with Sleeve-Core Structure and Its Effect on Room-Temperature Yield Asymmetry Via Bimetal Casting-Co-extrusion

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

Combined-extrusion techniques for fabricating yield-symmetric ZK61 magnesium alloys rods focusing on texture influence on their mechanical responses

Abnormal Extrusion Texture and Reversed Yield Asymmetry in a Mg–Y-Sm-Zn-Zr Alloy

Dynamic Compressive Behaviour and Microstructural Evolution of Extrusion-Shear Mg–6Zn–1Cu–1Y–0.6Zr Alloy

Tension–Compression Yield Asymmetry Influenced by the Variable Deformation Modes in Gradient Structure Mg Alloys

Role of Volume Fraction of Second Phase Particles, Dislocation-Twin and Twin-Twin Interactions in the Reduced Tension-Compression Yield Asymmetry