Abstract:Cu 1.8 S-based thermoelectric (TE) materials have garnered considerable interest due to their pollution-free, low-cost, and superior performance characteristics. However, high Cu vacancy and Cu migration inhibit their performance and electrical stability improvement. Through mechanical alloying and spark plasma sintering, a series of Cu 1.8 S and Mn x Cu 1.8 -S 0.5 Se 0.5 (0.01 ≤ x ≤ 0.06) bulk samples were prepared in this study. With Se alloying and Mn doping, the configuration entropy of Mn x Cu 1.8 S 0.5 Se 0.5 increases from low-entropy 0.4 R * for pristine Cu 1.8 S to medium-entropy 1.2 R * for Mn x Cu 1.8 S 0.5 -Se 0.5 . Mn x Cu 1.8 S 0.5 Se 0.5 subsequently crystallized in a cubic phase with enhanced symmetry and Mn solid solubility. High solubility enables the filling of excessive Cu vacancies, the reduction of carrier concentration, the adjustment of band structure, the enhancement of the Cu migration energy barrier, and the inhibition of Cu migration. Even at current densities exceeding 25 A cm −2 at 750 K, the resistance of Mn 0.03 Cu 1.8 S 0.5 Se 0.5 remained hardly changed, indicating a vastly improved electrical stability. In addition, the ultralow thermal conductivity of the lattice is achieved by decreasing the sound velocity and softening the lattice. At 773 K, the bulk ZT of Mn 0.06 Cu 1.8 S 0.5 Se 0.5 reaches a maximum of 0.79, which is twice that of pure Cu 1.8 S. The results indicate that combining entropy engineering and Cu vacancy engineering is an effective strategy for developing high-performance Cu 1.8 S TE materials.

High Thermoelectric Performance in Earth‐Abundant Cu3SbS4 by Promoting Doping Efficiency Via Rational Vacancy Design

Approaching high thermoelectric performance in p-type Cu3SbS4-based materials by rational electronic and nano/microstructural engineering

Unconventional Doping Effect Leads to Ultrahigh Average Thermoelectric Power Factor in Cu 3 SbSe 4 ‐Based Composites

Unconventional Doping Effect Leads to Ultrahigh Average Thermoelectric Power Factor in Cu3SbSe4‐Based Composites

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Enhanced Thermoelectric Properties of Earth-Abundant Cu2sns3 Via in Doping Effect

Unlocking the Potential of Cu3SbSe3: Ultralow Thermal Conductivity and Enhanced Thermoelectric Performance

Enhancing thermoelectric performance of Cu1.8S by Sb/Sn co-doping and incorporating multiscale defects to scatter heat-carrying phonons

Chemical Bonding Engineering for High-Symmetry Cu2S-based Materials with High Thermoelectric Performance

Toward Ultrahigh Thermoelectric Performance of Cu2SnS3‐Based Materials by Analog Alloying

Enhancing the Thermoelectric Performance of Bi 2 S 3 : A Promising Earth-Abundant Thermoelectric Material

Doping-mediated stabilization of copper vacancies to promote thermoelectric properties of Cu2−xS

Achieving a High Thermoelectric Performance of Tetrahedrites by Adjusting the Electronic Density of States and Enhancing Phonon Scattering

High Thermoelectric Performance in Cu2SnS3 by Control Over Phase‐Dependent Mobility Edge

Realized High Power Factor and Thermoelectric Performance in Cu3SbSe4

High Thermoelectric Performance of Cu3SbSe4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Synergistically enhanced thermoelectric properties of Bi2S3 bulk materials via Cu interstitial doping and BiCl3 alloying

Enhanced Thermoelectric Performance of Sn-doped Cu3SbS4

High Thermoelectric Performance of Cu 3 SbSe 4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Rare Earth Chloride Compositing and Multiscale Structure Lead to High Thermoelectric Performance in P-Type Cu3SbSe4

Enhanced Thermoelectric Properties and Electrical Stability for Cu 1.8 S-based Alloys: Entropy Engineering and Cu Vacancy Engineering