Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Comparison of Isotropic and Anisotropic Yield Criteria Models in Quenching Residual Stress of Magnesium Alloys

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Investigation on the inhomogeneous deformation of magnesium alloy during bending using an advanced plasticity model

Numerical simulation of the residual stress in the Mg-5Zn-3.5Sn-1Mn-0.5Ca-0.5Cu alloy with different extrusion parameters

The Flow Stress Behavior and Physical-Based Constitutive Model for As-Quenched Al-Zn-Mg-Cu Alloy

Simulation Study on Temperature and Stress Fields in Mg-Gd-Y-Zn-Zr Alloy during CMT Additive Manufacturing Process

Effects of Quenching Cooling Rate on Residual Stress and Mechanical Properties of a Rare-Earth Wrought Magnesium Alloy

Influence of Initial Yield Strength Weighting on Residual Stresses in Quenched Cylinders Using Finite Element Analysis

Experiment and Modeling of Plastic Anisotropy for AZ31B Mg-Alloy

Comparison of two different constitutive equations for hot deformation of AZ91 magnesium alloy

Modeling of 3D Plastic Anisotropy and Asymmetry of Extruded Magnesium Alloy and Its Applications in Three-Point Bending

A Constitutive Model for Asymmetric Cyclic Hysteresis of Wrought Magnesium Alloys under Variable Amplitude Loading

Residual Stresses in Spray Quenched EW75 Magnesium Alloy

Construction of an Arrhenius constitutive model for Mg-Y-Nd-Zr-Gd rare earth magnesium alloy based on the Zener-Hollomon parameter and objective evaluation of its accuracy in the twinning-rich intervals

The strain rate sensitive and anisotropic behavior of rare-earth magnesium alloy ZEK100 sheet

Establishment and Application of Flow Stress Models of Mg-Y-Mm-Zr Alloy

Influences of stress states and loading directions on the anisotropic fracture of magnesium alloy AZ31B sheet under tension-dominated forming conditions

Stress-state dependency of ductile fracture in an extruded magnesium alloy and its underlying mechanisms

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Comparison of three state-of-the-art crystal plasticity based deformation twinning models for magnesium alloys

Mg-3Al-1Zn alloy deformed along different strain paths: Role of latent hardening