Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Investigation on the inhomogeneous deformation of magnesium alloy during bending using an advanced plasticity model

Modeling of 3D Plastic Anisotropy and Asymmetry of Extruded Magnesium Alloy and Its Applications in Three-Point Bending

Predicting Plastic Behavior of Magnesium Alloy Tube Bending with Comprehensive Constitutive Models

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

On the inhomogeneous deformation behavior of magnesium alloy beam subjected to bending

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Non-associated anisotropic plasticity of metal sheets based on the distortional concept

Failure prediction of magnesium alloys based on improved CDM model

Physical-based constitutive model considering the microstructure evolution during hot working of AZ80 magnesium alloy

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Mg-3Al-1Zn alloy deformed along different strain paths: Role of latent hardening

Experiment and Modeling of Plastic Anisotropy for AZ31B Mg-Alloy

Deformation Analysis of Magnesium Alloy Based on Crystal Plasticity Theory

Establishment and Application of Flow Stress Models of Mg-Y-Mm-Zr Alloy

A Constitutive Model for Asymmetric Cyclic Hysteresis of Wrought Magnesium Alloys under Variable Amplitude Loading

Enhanced Cyclically Stable Plasticity Model for Multiaxial Behaviour of Magnesium Alloy AZ31 under Low-Cycle Fatigue Conditions

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Micromechanical modeling and evaluation of CNTs reinforced magnesium matrix composites based on stress softening modified constitutive model

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Hot Deformation Characteristics and Dynamic Recrystallization Mechanisms of a Semi-Solid Forged AZ91D Magnesium Alloy

Plasticity evolution of an aluminum-magnesium alloy under abrupt strain path changes