Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Researoh on precipitation behavior of nanoscale second phase in carburized gear steels

Study of Transformation Characteristics and Nano-Scale Precipitation in Nb Microalloyed Steel

Applications and Thermodynamic Analysis of Equilibrium Solution for Secondary Phases in Ti–N–C Gear Steel System with Nano-Particles

Microscopic Phase-Field Simulation for Precipitation Behavior of Ni-Al-Cr Alloy During Two-Step Aging

On the grain coarsening behavior of 20CrMnTi gear steel during pseudo carburizing: A comparison of Nb-Ti-Mo versus Ti-Mo microalloyed steel

Effect of Precipitation of (ti,v)n and V(C,N) Secondary Phases on Mechanical Properties of V and N Microalloyed 1cr Steels

Microstructural Evolution and Precipitation Strengthening In a New 20Cr Ferritic Trial Steel

Microscopic Phase-field Simulation of Effects of Re-ageing Temperature on Precipitation of Ni-Al-Cr Alloys

Influence of Heating and Cooling Rate on Dissolution and Precipitation Behavior of Nickel-based Single Crystal Superalloy

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

An Analysis on Precipitated Phase Particles in Low Carbon Micro-Alloying Dual Phase Steel

Effect of Precipitated Particles on Austenite Grain Growth of Al- and Nb-Microalloyed 20MnCr Gear Steel

New Insights into the Precipitation Strengthening of Ferritic Steels: Nanoscale G-phase Particle

Suppression of Austenite Grain Coarsening by Using Nb–Ti Microalloying in High Temperature Carburizing of a Gear Steel

The precipitation behavior of second phase in high titanium microalloyed steels and its effect on microstructure and properties of steel

Nanoprecipitation in bearing steels

Interphase precipitation behavior of nano-sized carbides in low carbon steel

Thermodynamic calculations of the second-phase precipitation in Nb-Ti microalloyed steel

Precipitation Behavior of the Second Phase in High-Nitrogen Austenitic Stainless Steel Alloyed with V and Nb

B2 phase precipitation behavior in Ti–40Al–8Nb alloys during the hot deformation process

Effect of Cooling Rates on the Second‐Phase Precipitation and Proeutectoid Phase Transformation of a Nb–Ti Microalloyed Steel Slab