Abstract:Pitting and localized corrosion of carbon steel is considered to be a complex process influenced by a wide range of parameters such as temperature, bulk solution pH, and chloride ion concentration. Solution pH is known to influence corrosion product characteristics and morphology in CO2- and H2S-containing corrosion systems. However, from the perspective of pitting corrosion in CO2-saturated environments, the extent to which bulk pH of solutions and the presence of corrosion products influence localized attack is still not clearly understood. This paper presents an investigation into the role of pH on the characteristics of corrosion product and pitting corrosion behavior of X65 carbon steel (UNS K03014) in CO2-saturated brine. Pitting corrosion studies were conducted over 168 h at 50°C in 3.5 wt% NaCl solutions at different bulk pH (buffered to pH values of 6.6 and 7.5 in some cases) in order to understand and correlate the role of pH on corrosion product morphology, chemistry, initiation, and propagation of pits within each distinct environment. Corrosion product composition and morphology are identified through a combination of electrochemical and surface analysis techniques, which include scanning electron microscopy and x-ray diffraction. The extent of corrosion damage of the carbon steel is evaluated through the implementation of surface interferometry to study discrete pit geometry, namely the size, depth, and aspect ratio. Results indicate that the process of pit initiation and propagation of carbon steel in CO2 corrosion environment is different depending upon bulk solution pH. At low pH (pH values starting at 3.8), pitting initiates faster and propagates steadily along with significant uniform corrosion resulting from the formation of an “amorphous” form of FeCO3. At higher pH, uniform corrosion is significant, while pitting initiates with increasing protection from crystalline FeCO3. At a pH value of 7.5, pitting corrosion initiation occurs after and/or during pseudo-passivation is achieved as a result of the formation of a “protective and pseudo-passivating” FeCO3 film.

Ph-Dependent Corrosion Initiation Behavior Induced by Inclusions of Low Alloy Steel in Simulated Marine Environments

Influence of Inclusions on Initiation of Pitting Corrosion and Stress Corrosion Cracking of X70 Steel in Near-Neutral Ph Environment

The Influence of pH on Localized Corrosion Behavior of X65 Carbon Steel in CO2-Saturated Brines

Insight into the Triggering Effect of (al, Mg, Ca, Mn)-oxy-sulfide Inclusions on Localized Corrosion of Weathering Steel

Effect of pH on pitting corrosion of stainless steel welds in alkaline salt water

Role of Inclusion and Microstructure on Corrosion Initiation and Propagation of Weathering Steels in Marine Environment

Pitting Corrosion of 304 L Stainless Steel Welds in Simulated Concrete Pore Solutions

Effect of pH and chloride on the micro-mechanism of pitting corrosion for high strength pipeline steel in aerated NaCl solutions

Influence of SO42- on the Corrosion Behavior of Q235B Steel Bar in Simulated Pore Solution

Electrochemical Corrosion Behavior of the Stainless Steel and Welding Seam in Simulation Concrete Pore Fluid

The Electrochemical Behaviour of 2205 Duplex Stainless Steel in Alkaline Solutions with Different Ph in the Presence of Chloride

Experimental Study on Erosion-Corrosion of Carbon Steel in Flowing NaCl Solution of Different Ph

New insights into the mechanism of localised corrosion induced by TiN-containing inclusions in high strength low alloy steel

The Early-Stage Propagation of Localized Corrosion of a Sintered NdFeB Alloy in Aqueous Environments

Dissolution kinetics of the sulfide-oxide complex inclusion and resulting localized corrosion mechanism of X70 steel in deaerated acidic environment

Electrochemical Study of Steel Corrosion in Saturated Calcium Hydroxide Solution with Chloride Ions and Sulfate Ions

Research on Pitting Corrosion of Micro-alloyed High Strength Steel Bars

Failure analysis of anion synergy on pitting behavior of liner 316L in sour water system by electrochemical tests

Microscopic investigation on pitting corrosion of Ni-Cr-Mo-V high-strength steel weldment in simulated deep-sea environment

Direct observation of pitting corrosion evolutions on carbon steel surfaces at the nano-to-micro- scales

Towards a better understanding of localised corrosion induced by typical non-metallic inclusions in low-alloy steels