Abstract:Lamellar globularization in the dual-phase titanium alloy is the key to improving plasticity and strength. However, the mechanism has not been fully elucidated so far. In this work, the role of phase/grain bound-ary in the static globularization of TC17 alloy was systematically studied by setting different alpha phase con-tent before annealing through low-and high-temperature deformation. Isothermal compression causes the parallel distribution and fragmentation of 3D alpha plates and few globular alpha particles are formed at a strain rate of 1 s -1 . Post-deformation annealing promotes the static globularization of alpha phase while it is affected by initial alpha phase content. After 730 degrees C deformation, the development of alpha/alpha interface by absorbing dislocations promotes the formation of globular alpha grains based on the nucleation of sepa-rated alpha particles and pre-recovery alpha subgrain during subsequent annealing. The alpha/alpha/P and alpha/P/P triple junctions formed due to high alpha content with about 36% volume fraction are favorable for the further nucleation and growth of globular alpha grains by reducing interface energy, forming a 3D irregular alpha plate. Then nucleation and growth of the P phase dominate the microstructure evolution during subsequent an-nealing, resulting in the local dissolution of the plate and formation of alpha rods. After 850 degrees C deformation, the alpha phase tends to nucleate at the P/P/P triple junctions and grow into a lamellar shape along the high energy P/P grain boundary due to low alpha content with about 7% volume fraction. The alpha nucleation that maintains the Burgers orientation relationship (BOR) with the surrounding P phase grows along the habit plane and thickens slowly, resulting in the formation of a precipitated alpha plate with a flat surface and the suppression of static globularization. The comprehensive investigation of lamellar globularization provides guidance for optimizing the 3D microstructure and properties of dual-phase titanium alloy.(c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Precipitation and Evolution Behaviors of Grain Boundary Α and Α Side Plates for Ultra-High Strength Titanium Alloy During Continuous Cooling

Effect of low-angle grain boundaries on morphology and variant selection of grain boundary allotriomorphs and Widmanstätten side-plates

Morphology evolution and orientation characteristics of precipitate of ultra-high strength titanium alloy

Evolution of grain boundary α phase during cooling from β phase field in a α + β titanium alloy

Growth behavior and variant selection of grain boundary α in Ti6246

Study on Bifurcation Behavior and Morphology of the Secondary Grain Boundary Α Phase in TC18 Titanium Alloy

Crystal Orientation and Morphology of Α Lamellae in Wrought Titanium Alloys: on the Role of Microstructure Evolution in Β Processing

Origin of Morphological Variation of Grain Boundary Precipitates in Titanium Alloys

Influence of alternate grain boundary on the development of Widmanstatten microstructure in TC21 Ti alloy

Influence of alternate grain boundary α on the development of Widmanstätten microstructure in TC21 Ti alloy

Formation and Evolution of New Α Grain Boundary and Its Influence on Globularization of Α Lamellae in TC17 Alloy

Mesoscale Deformation Mechanisms in Relation with Slip and Grain Boundary Sliding in TA15 Titanium Alloy During Tensile Deformation

Effect of Boundary on the Alpha Phase Precipitation in a Near-Alpha Titanium Alloy

Precipitation Behaviors And Orientation Evolution Mechanisms Of Alpha Phases In Ti-55511 Titanium Alloy During Heat Treatment And Subsequent Hot Deformation

Grain boundary α-phase precipitation and coarsening: Comparing laser powder bed fusion with as-cast Ti-6Al-4V

Growth Mechanism of Αp and Interface Relationships Between Αp and Αs During Cooling of a Near Α Titanium Alloy

High-temperature Behaviors of Grain Boundary in Titanium Alloy: Modeling and Application to Microcrack Prediction

Effects of the morphology of grain boundary α-phase on the anisotropic deformation behaviors of additive manufactured Ti–6Al–4V

Effect of Cooling Rate on α Variant Selection and Microstructure Evolution in TB17 Titanium Alloy

Phase/grain Boundary Assisted-3D Static Globularization Mechanism of TC17 Alloy Based on the Microstructure Reconstruction and In-Situ TEM Observation

The precipitation mechanism of secondary -phase and formation of a bimodal microstructure in Ti6242S alloy cooled from the plus phase field