Abstract:The microstructure evolution and fracture behavior of Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe (Ti-5321) alloy during BASCA (β annealed with subsequent slow cooling & aging) heat treatment were studied. Three different lamellar microstructures, termed as L1, L2 and L3, were obtained by solution treated at 880 °C for 2 h followed by 0.5 °C/min cooling to 800 °C, 750 °C and 710 °C, respectively and aging at 580 °C for 6 h. Microstructural investigation revealed that the three lamellar microstructures were composed of intergranular precipitation (αGB, αWGB), intragranular αl and βt. Both of the volume fraction of lamellae α and the size of α colonies increased with the increasing furnace cooling time. Both intergranular and intragranular precipitation in L1, L2 and L3 obeyed the Burgers orientation relationship (OR) with adjacent β grain. However, the texture intensity and variant selection degree of lamellar α increased with cooling process owing to the increased amount of α colonies. In addition, the L1 sample, with 15% αl, displayed the lowest fracture toughness value (57.7 MPa·m1/2), while the L3 sample with 61% αl exhibited the highest (114 MPa·m1/2). Although the crack path in all the cases were both translamellar and interlamellar, fracture mode varied from mixed mode (dimples and intergranular cracks) type fracture in L1 to predominantly dimple fracture in L2 and L3. Moreover, the fracture behavior of Ti-5321 alloy was also related to the crystallographic distribution and variation selection of α phase. Crack growth was much easier through continuous αGB layer compared to the discontinuous αGB, especially for the high angled αGB/αGB grain boundary. As a consequence, the higher probabilities of misorientation angles of 90° in L1 and L3 could significantly promote crack deflection compared to L2.

Influence of alternate grain boundary on the development of Widmanstatten microstructure in TC21 Ti alloy

Influence of alternate grain boundary α on the development of Widmanstätten microstructure in TC21 Ti alloy

Evolution of grain boundary α phase during cooling from β phase field in a α + β titanium alloy

Growth behavior and variant selection of grain boundary α in Ti6246

Effect of low-angle grain boundaries on morphology and variant selection of grain boundary allotriomorphs and Widmanstätten side-plates

Variant selection of α precipitates formed at β triple junctions in titanium alloy

The precipitation mechanism of secondary α-phase and formation of a bimodal microstructure in Ti6242S alloy cooled from the α + β phase field

Evolution mechanism of lamellar α and interlayered β during hot compression of TC21 titanium alloy with a widmanstätten structure

Origin of Morphological Variation of Grain Boundary Precipitates in Titanium Alloys

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effect of cooling rate on α variant selection and microstructure evolution in a near β Ti–5Al–3Mo–3V–2Cr–2Zr–1Nb–1Fe alloy

Effect of Cooling Rate on α Variant Selection and Microstructure Evolution in TB17 Titanium Alloy

Influences of Deformation Strain, Strain Rate and Cooling Rate on the Burgers Orientation Relationship and Variants Morphology During Β→α Phase Transformation in a Near Α Titanium Alloy

In situ observation of competitive growth of α grains during β → α transformation in laser beam manufactured TiAl alloys

Evolution of microstructure and intervariant boundaries of α phase in electron beam melted and heat-treated Ti–6Al–4V alloy

Microstructure evolution and fracture behavior of Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe alloy during BASCA heat treatments

Morphology evolution and orientation characteristics of precipitate of ultra-high strength titanium alloy

Electron structure of gamma/alpha(2) phase boundaries in TiAl based alloys

Precipitation behaviors and orientation evolution mechanisms of α phases in Ti-55511 titanium alloy during heat treatment and subsequent hot deformation

Effects of the morphology of grain boundary α-phase on the anisotropic deformation behaviors of additive manufactured Ti–6Al–4V

Effect of Pre-Deformation in the Β Phase Field on the Microstructure and Texture of the Α Phase in a Boron-Added Β-Solidifying TiAl Alloy