Abstract:Because of the promising corrosion resistance and load-bearing capacity, titanium-clad (TC) bimetallic steel has gained increasing attention in ocean/coastal civil and structural engineering. Due to the double-layer nature of TC bimetallic steel, the characteristics of the structural member’s geometry and weld details are considerably different from that of conventional steel members. Even though previous studies have conducted systematical clarifications on parent material of TC bimetallic steels, the mechanical behaviors of weld joints are still vague. This paper firstly describes the manufacture features of TC bimetallic steel welded joints and welded members. Subsequently, the type II and type III butt-welded joints provided by GB/T 13149-2009 are selected to study the corresponding tensile mechanical behavior. Two butt-welded TC bimetallic steel plates were fabricated from hot-rolled bonding TA2 + Q355B TC bimetallic steel and welding wire of ER55-Ni1 and ERTA2ELI. Eight tensile coupons were then extracted from the two welded plates and loaded to failure monotonically. The failure mechanism, stress–strain curves and key mechanical properties are studied and compared with that of parent material. It is found that both types of welded joints possess two fracture points. The first one refers to the fracture of weld joint between the clad layer and titanium cover plate, whilst the second one is the eventual fracture of substrate metal. When the first fracture point is reached, the stress–strain relation exhibits a sharp drop in stress value. Thereafter, a strain-hardening behavior can still be observed prior to the ultimate strength point. The first fracture-induced stress drop of type II joint is less than that of type III joint, whilst the strain-hardening amount of type II joint is more outstanding than that of type III joint. The fracture elongations of type II joint and type III joint are respectively 37% and 57% that of the parent material, whilst the proportions between the ultimate strengths of welded joints and parent material are, respectively, 90% and 93%. In general, the two types of TC bimetallic steel weld joints investigated herein exhibit favorable load-bearing capacity but unfavorable ductility and deformability. Based upon the experimental results, the structural design methodology of welded TC bimetallic steel structure is discussed. The investigations conducted in this paper can provide reference for development of structural design theory of welded TC bimetallic steel structure.

High-cycle Fatigue Properties of Explosion Bonded Titanium-Clad Bimetallic Steel

High-Cycle Fatigue Properties of Titanium-Clad Bimetallic Steel with Different Interfacial Conditions

Fatigue Properties of Titanium-Clad Bimetallic Steel Butt-Welded Joints

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Low-cycle Fatigue Behaviour of Hot-Rolled Titanium-Clad Bimetallic Steel

Low-cycle fatigue behavior for stainless-clad 304+Q235B bimetallic steel

Experimental cyclic behaviour and constitutive modelling of hot-rolled titanium-clad bimetallic steel

Cyclic Behavior of Hot-Rolled Titanium-Clad Bimetallic Steel under Large Plastic Strain Reversals

Material Properties and Stress-Strain Curves for Titanium-Clad Bimetallic Steels

Post-fire mechanical properties of titanium–clad bimetallic steel in different cooling approaches

Fatigue Crack-Initiation Mechanisms of a Dual-Phase Titanium Alloy Exhibiting High Tensile and High-Cycle Fatigue Properties

CRACK PROPAGATION ALONG THE INTERFACE OF EX-PLOSIVE BONDED 1cr18ni9ti/20g PLATE

Research Progress of Titanium Alloys and Their Diffusion Bonding Fatigue Characteristics

Low-cycle Fatigue Behaviour and Fracture Feature of Stainless-Clad Bimetallic Steel

Effect of Heat Treatment on Very High Cycle Fatigue Properties of TC4

Tensile Behavior of Titanium-Clad Bimetallic Steel Butt-Welded Joints

A novel high entropy composite interlayer for diffusion bonding of TC4 titanium alloy to 316 L stainless steel

Microstructure Evolution and Fatigue Crack Growth of Diffusion Bonded Ti-6Al-4V Titanium Alloy

Fatigue property and failure mechanism of TC4 titanium alloy in the HCF and VHCF region considering different forging processes

Achieving Excellent Fatigue Crack Growth Resistance and Tensile Strength Combination in Multilayered TC4/TB8 Structures

High cycle fatigue behavior of titanium microalloyed high-strength beam steels