Abstract:In the present work, nickel-base composite powder (Ni60), nickel-base composite powder with the addition of h-BN solid lubricants (h-BN/Ni60) and nickel-base composite powder with the addition of nano-Cu encapsulated h-BN solid lubricants (nano-Cu/h-BN/Ni60) were used as raw materials to synthesize three different coatings on Q235 steels by laser cladding. Microstructures of these coatings were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Raman spectroscopy. Tribological properties of these coatings were investigated at the temperatures from 25 °C to 600 °C. High temperature micro-hardness measurement was performed by Vickers micro-hardness tester. The results showed that the h-BN particles survived after laser cladding and displayed a homogeneous distribution in the nickel-base composite matrix. The encapsulation of h-BN by nano-Cu resulted in an increase of h-BN content in the coating. Although the addition of nano-Cu and h-BN led to a decrease on hardness, the nano-Cu/h-BN/Ni60 coating had the lowest friction coefficient and wear rate among the three coatings in a wide range of temperature from 25 °C to 500 °C. The mechanism of wear reduction by addition of nano-Cu encapsulated h-BN solid-lubricants was also discussed in this research.

High Temperature Low Friction Behavior of H-Bn Coatings Against ZrO2

Tribological behavior of h -BN/Al 2 O 3 self-lubricating composites in extreme environments–Part I: Lubricating behavior and ultra-low friction coefficient mechanism in air environments from room temperature to 1200 °C

Influence of CePO4 on High Temperature Anti-Friction and Anti-Wear Behaviors of Nickel-Based H-Bn Composite Coatings

Tribological Behavior of H-Bn/al2o 3 Self-Lubricating Composites in Extreme Environments-Part - Part I: Lubricating Behavior and Ultra-Low Friction Coefficient Mechanism in Air Environments from Room Temperature to 1200 ° C

Tribological Behavior of H-Bn/al2o3 Self-Lubricating Composites in Extreme Environment-Part II: Self-lubrication and Mechanism in Water-Oxygen Environment from 300 °C to 1200 °C

Transformation-induced High Temperature Low Friction Behaviors of ZrO2-steel System at Temperatures Up to 900 °C

Tribological behavior under 1200°C elevated temperature of spark plasma sintered h -BN bulk

High-Temperature Superlubricity Performance of H-Bn Coating on the Textured Inconel X750 Alloy

High temperature oxidation resistance of hot-pressed h-BN/ZrO 2 composites

Mechanical and tribological properties of h-BN/ZrO2/SiC solid-lubricating ceramic composites

Tribological properties of h-BN matrix solid-lubricating composites under elevated temperatures

Investigations of high temperature synergetic tribological behavior of HVOF deposited Ni-based metallic coating with self-lubricating ceramic phase (h-BN)

Microstructure and performance of (CoCrNi) 88 Al 6 Ti 6 -cBN composite coatings by high-speed laser cladding (HSLC): A novel strategy for synergizing wear-resistance and friction reduction

Tribological behaviour of Ag–BN coatings prepared by plasma spraying

Tribological Behavior of Si3N4 - Hbn Ceramic Materials Against Stainless Steel under Dry Friction Condition

High Temperature Superlubricity Behaviors Achieved by AlSiN Coatings Against WS2 Coatings at 600 °C

Elevated-temperature Tribological Behavior of Ti–B–C–N Coatings Deposited by Reactive Magnetron Sputtering

Tribological Behavior of B4C/hBN Ceramic Composites Sliding against Ductile Iron in Emulsion

Evaluation of Tribological Behavior of B4C–hBN Ceramic Composites under Water-Lubricated Condition

Effect of Hbn Content on the Friction and Wear Characteristics of B4C–hBN Ceramic Composites under Dry Sliding Condition

Microstructure and tribological properties of laser cladded self-lubricating nickel-base composite coatings containing nano-Cu and h-BN solid lubricants