Abstract:Abstract The effect of Mg alloying on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant aluminum alloy was investigated by microstructure observation and tensile test. Alloying with 0.5 wt%Mg addition considerably increases the yield strength at 300 °C of samples at as-cast, as-solutionized and as-aged states. It also greatly enhances the strengthening effects from solution and ageing treatments, however, simultaneously, decreases the elongation greatly. During the solidification process of the alloy with Mg addition, a great amount of whisker-like Al–Cu–Mg compound phase is formed at the eutectic boundary zones in the form of ridge configuration, which is determined as AlCuMg intermetallic compound by TEM. During the solution treatment, this whisker-like AlCuMg phase is completely dissolved into Al matrix that leads to a remarkable rise in the increment of yield strength at 300 °C by solution strengthening. The alloying of Mg has a significant influence on the precipitation behavior during the ageing treatment, for examples, promoting the formation of finer θ ′′ particles and a great number of Cu–Mg atomic clusters. During high temperature tensile test, theses clusters evolve into fine cube-like Al 5 Cu 2 Mg particles with orthorhombic structure. It is the significant microstructure evolution induced by alloying of Mg that leads to the great rise in yield strength at 300 °C. Addition of Mg in Al–Cu–Mn–Ni alloy dose not lead to the formation of meta-stable or stable S phase, but whisker-like AlCuMg and cube-like Al 5 Cu 2 Mg compounds are determined by TEM.

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Effects of Low Nickel Content on Microstructure and High-Temperature Mechanical Properties of Al-7Si-1.5Cu-0.4Mg Aluminum Alloy

Microstructure and Mechanical Properties at Elevated Temperature of Mg-Al-Ni Alloys Prepared Through Powder Metallurgy

Ni-Rich Phases in Al-12%Si-4%Cu-1.2%Mn-x%Ni Heat-Resistant Alloys and Effect of Ni-Alloying on Tensile Mechanical Properties

Effects of Ni Content on Low Cycle Fatigue and Mechanical Properties of Al-12Si-0.9Cu-0.8Mg-xNi at 350 °C

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

Mechanical Properties and Oxidation Characteristics of TiNiAl(Nb) Intermetallics

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Effect of Ni Addition on the Solidification Process and Microstructure of Al-12%Si-4% Cu-1.2%Mn-x%Ni Heat-Resistant Alloys

Effects of Fe and Ni on Microstructure and High Temperature Mechanical Properties of Al-Cu-Mg-Ag Alloy

Effects of Ni on the Microstructure and Properties of Heat Resistant Cast Cu-Ni-Al Alloy

Microstructural Evolution and Mechanical Properties of Al-4Ni-0.4 V Alloyed with Zr and Ti at Elevated Temperatures

The strengthening role of micro-sized phases and nano-precipitates in Al–Mg 2 Si–Cu(–Ni) alloys at 25 °C and 350 °C

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

Microstructure Evolution and Tensile Properties of Conventional Cast TiAl-based Alloy with Trace Ni Addition

Mechanical Properties, Microstructure and Fracture Mechanism of 95W-3.5Ni-1.5fe Alloys at High Temperature

The Influence of Al–10Sr Or/ and Al–5Ti–1B on Microstructure and Mechanical Properties of Al–12Si–4Cu–2Ni–0.8 Mg Alloys

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Microstructure and Mechanical Properties of Cu–12Al–xNi Alloy Prepared Using Powder Metallurgy