Abstract:To improve the welding performance of aluminum alloys, a thermal source model of an irregular weld seam was established. COMSOL software was used for numerical simulation of the weld seam geometry effect on the temperature and stress fields in laser welding, which results were experimentally validated. The results show that the ellipsoidal laser welding melted micropool exhibited quasi-steady-state temperature field characteristics. The temperature gradient and thermal stress showed an increase followed by a decline. The temperature fluctuation amplitude of the square-tooth-shaped weld seam exceeded that of the arc-toothshaped one. The temperature evolution of the broken line tooth-shaped weld seam showed a slightly increasing trend, except for the inflection point. The experimental average tensile strength of the weld seam was the highest, reaching about 210 MPa, i.e., roughly 85% of the base material (245 MPa), which coincided with the COMSOL-based temperature field simulation results. With increasing deformation amplitude and transition radius, the maximum tensile force, tensile strength, and elongation at fracture showed an increasing trend. However, the deformation amplitude should be below a certain limit because its increase elongates the welding path and reduces the distance between weld seams, resulting in serious heat accumulation. The tensile fracture morphology of the 6063-T6 base material was curved shear, with shallow toughness pits, small tearing edges at the edges, and small granular objects, indicating small plastic deformation during the fracture process. The tensile fracture of the welded part spanned the weld seam and the base material, and the fracture occurred along the tangent direction of the weld seam. The fracture surface was smooth, the tearing edges at the edge of the toughness pit shifted along the weld seam direction, forming many co-directional slip bands, with highly pronounced plastic deformation.

Mechanical Characterization and Prediction of Aluminum Alloy Laser Welding Joints Including Roles of Geometries and Porosity

Experimental investigations on mechanical properties of AA6061-T6 aluminum alloy joined by laser welding using digital image correlation

Microstructural, Porosity and Mechanical Properties of Lap Joint Laser Welding for 5182 and 6061 Dissimilar Aluminum Alloys under Different Place Configurations

Effect of Porosity Morphology and Elements Characteristics on Mechanical Property in T-joints During Dual Laser-Beam Bilateral Synchronous Welding of 2060/2099 Al-Li Alloys

Effect of swinging laser on porosity, microstructure, and mechanical properties of laser welded aluminum alloy joints with different lap forms

Porosity, Element Loss, and Strength Model on Softening Behavior of Hybrid Laser Arc Welded Al-Zn-Mg-Cu Alloy with Synchrotron Radiation Analysis

New insight into microstructure and mechanical properties of heterostructures 7075 Al joint prepared via single mode laser welding

Thermal and Fluid Flow Characteristics and their Relationships with Porosity in Laser Welding of AA5083

Investigation of the Inhibition Mechanism of Process Porosity in Laser-MIG Hybrid-Welded Joints for an Aluminum Alloy

Prediction and Optimization of Tensile Properties of 2219-T8 Aluminum Alloy TIG Welding Joint by Machine Learning

Effect of nanosecond pulse laser power on welding interface and mechanical properties of AZ31B Mg/6061 Al

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding

Microstructural Inhomogeneity in the Fusion Zone of Laser Welds

Effect of post-weld heat treatment on the microstructure, phase composition and mechanical properties of dissimilar Al-Mg-Li/Al-Cu-Li laser welded joints

Investigation of the microstructure and mechanical properties of Mg–Al–Zn alloy joints formed by different laser welding processes

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

Effect of Laser Power on Microstructure and Properties of 6061 Aluminum Alloy Welded Joint

Laser Weld Seam Curved Path Effect on 6063 Aluminum Alloy Strength and Temperature Distributions: COMSOL Numerical Simulation

Laser-Arc Hybrid Welding Process and Joint Performances of 6106-T6 Aluminum Alloy Profiles for High Speed Trains

Tensile failure analysis of laser stake-welded T-joints: X-ray tomography based conformal finite element and fractal theoretical approaches

Porosity inhibition of aluminum alloy by power-modulated laser welding and mechanism analysis