Abstract:The next generation autonomous sensor nodes are being developed towards ultra-low-power with on-node signal processing capability. The former facilitates battery-less and miniaturized sensors relying on harvested energy, while the latter enables intelligent System-on-Chip (SoC) to sense and process multimodal parameters locally on the sensor nodes. As for analog front-end (AFE), a straightforward solution for low power and digital compatibility is to reduce its supply voltage to the sub-volt range. However, supply scaling is less friendly to conventional AFEs, which often require large dynamic range (DR) and high linearity, Furthermore, practical considerations of low noise, high input-impedance $(\mathrm{Z}_{\text{in}})$ and sensor-dependent bandwidth (BW) further exacerbate the challenges to comply with versatile sensors. To realize the low-voltage AFE, time-domain (TD) direct digitization architectures [1]–[5] were proposed (Fig. 1). The $\mathrm{G}_{\mathrm{m}}-\mathrm{C}$ based delta-sigma modulator $(\Delta\Sigma \mathrm{M})$ with a built-in TD loop filter benefits from high input impedance and higher order noise shaping [1], but the $\mathrm{G}_{\mathrm{m}}$ exhibits nonlinearity for a large input signal. Alternatively, the VCO-based AFEs provide better supply voltage scalability and inherent ${1}^{\text{st}}$ -order noise shaping. The open-loop VCO-based AFE [2] benefits from a small chip area, but suffering from the tradeoff between linearity and input range. While the closed-loop VCO-based AFE solves this issue [3]–[5], this topology often needs a highly linear feedback DAC that notably reduces the input impedance of the AFE, unless impedance boosting buffers are used [6]. Besides, the closed-loop VCO based AFEs needs to be clocked continuously, resulting in power overhead.

A Wideband and High Output Swing Analog Frontend Circuit for FMCW LiDAR

A Wide Dynamic Range Analog Front-End with Reconfigurable Transimpedance Amplifier for Direct ToF LiDAR

A CMOS AFE Array With DC Input Current Cancellation for FMCW LiDAR

A 16-Channel 12-Bit Rail-to-rail Successive Approxmation Register ADC for AFEs

A 0.5V 723nw 84.3Db-Sndr Dynamic Zoom ADC with CLS-Assisted Capacitively-Biased FIA

Intermediate Frequency Circuit Design for a 60ghz LFMCW Radar

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A 16-Channel Analog CMOS SiPM with On-Chip Front-End for D-ToF LiDAR

High Sensitivity and Wide Dynamic Range Analog Front-End Circuits for Pulsed TOF 4-D Imaging LADAR Receiver

A TDM-based Analog Front-End for Ear-EEG Recording with 74.5-GΩ Input Impedance, 384-mV DC Tolerance and 0.27-μVrms Input-Referred Noise

An AC Coupling Ultrasound Analog Front-End Architecture with A Three-stage DCOC

Low-Noise Low-Power Ultrasound AFE with Continuous TGC Built in Both TIA and Beamformer.

A Fully Solid-State Beam Scanner for FMCW LiDAR Application

A Three-stage Analog Low-Frequency Drift Calibration and DC Offset Correction Circuit for Ultrasonic AFE

Hybrid Integrated Ultralow-Linewidth and Fast-Chirped Laser for FMCW LiDAR

IF Amplifier Module for High-Sweep Speed LFMCW Radar

28-Nm CMOS Ultrasound AFE with Split Attenuation for Optimizing Gain-Range, Noise, and Area

A CMOS Optoelectronic Transimpedance Amplifier Using Concurrent Automatic Gain Control for LiDAR Sensors

A Low-Power, High-Resolution Analog Front-End Circuit for Carbon-Based SWIR Photodetector

A 0.8V/0.6V 2.2μw Time-Domain Analog Front-End with $540\text{mv}_{\text{pp}}$ Input Range, 81.6db SNDR and $80\mathrm{m}\omega$ Input Impedance.

A 15.5-ENOB 335 Mvpp-Linear-input-range 4.7-Gω-input-impedance CT-ΔΣM Analog Front-End with Embedded Low-Frequency Chopping