Abstract:A recently developed single shear specimen (SSS) was used to investigate the thermo-viscoplastic behavior of 2024-T351 aluminum alloy (AA2024-T351) under simple shear stress state. Shear stress-shear strain relations over a wide range of strain rates, covering low (0.001 and 0.1 sâˆ’1), medium (10 sâˆ’1), high (3000 and 6000 sâˆ’1) and very high (14000-49000 sâˆ’1) regimes and at initial temperatures from 293 to 573 K were obtained experimentally. The results show that: (1) at 293 K, AA2024-T351 exhibited negligible strain rate sensitivity at strain rates below 6000 sâˆ’1, and the effect of strain rate became obvious at strain rates above 14000 sâˆ’1; (2) dynamic strain aging (DSA) occurred at temperatures between 373 and 573 K and strain rates below 6000 sâˆ’1; (3) strain rate sensitivity of the material was strongly affected by DSA, and bell-shaped strain rate sensitivity curves were observed; (4) with an increase in temperature, peak values of the bell-shaped strain rate sensitivity curves shifted to higher strain rates. A constitutive model taking the advantages of Johnson-Cook model, Khan-Huang-Liang model, Nemat-Nasser-Li model and Wang-Guo-Gao model was developed for deformation behavior description, with the effects of viscous drag on dislocation motion and DSA considered. The experimental flow stress curves were compared to the model predictions, and a good agreement was observed. To validate the constitutive model independently of the experiments used for the identification of the model parameters, numerical simulations of Taylor impact tests were performed. A good agreement between experimental and numerical post-test specimens, in terms of mushroom shaped specimen head and reduced specimen length, was observed. According to the numerical results, strain rates varied largely between 103 and 106 sâˆ’1 during Taylor impact tests. Besides, numerical simulations of Taylor impact tests were performed again using the constitutive model excluding the viscous drag component, and less accurate numerical results were obtained. It implies that for precise computations of engineering applications, the actual strain rate should be considered in the establishment of constitutive models.

Strain Rate Sensitivity Behavior of 2219 Aluminum Alloy Under Dynamic Compression

Dynamic constitutive model and deformation mechanism of 2219 aluminum alloy based on the dynamic interruption‐recovery

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Strain Rate Sensitivity and Adiabatic Shear Deformation of an Advanced Al-Mg Alloy

Static Softening Behavior and Modified Kinetics of Al 2219 Alloy Based on a Double-Pass Hot Compression Test

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

Strain Rate Effects on the Mechanical Properties of an AlCoCrFeNi High-Entropy Alloy

The Study on Forming Property at High Temperature and Processing Map of 2219 Aluminum Alloy

High Strain Rate Deformation of Heat-Treated AA2519 Alloy

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

A Physically Based Constitutive Model and Continuous Dynamic Recrystallization Behavior Analysis of 2219 Aluminum Alloy during Hot Deformation Process

Microstructural Evolutions of AA7055 Aluminum Alloy under Dynamic and Quasi-static Compressions

Influence of Pre-Straining and Heating on Strain-Rate Sensitivity of AA5182-O

Dynamic Behavior of Aluminum Alloy Aw 5005 Undergoing Interfacial Friction and Specimen Configuration in Split Hopkinson Pressure Bar System at High Strain Rates and Temperatures

Dynamic mechanical behaviors of 6082-t6 aluminum alloy

Research and Revise on Constitutive Equation of 7050-T7451 Aluminum Alloy in High Strain Rate and High Temperature Condition

The Effects of Strain Rate and Anisotropy on the Formability and Mechanical Behaviour of Aluminium Alloy 2024-T3

The Dynamic Recrystallization in a Hot Compressed Al‐Zn‐Mg‐Cu‐Sc‐Zr Alloy: the Role of Strain Rate

Study on Dynamic Impact Response and Optimal Constitutive Model of Al-Mg-Si Aluminum Alloy

Strain-Rate-Dependent Tensile Response of Ti–5Al–2.5Sn Alloy

Simple shear behavior of 2024-T351 aluminum alloy over a wide range of strain rates and temperatures: Experiments and constitutive modeling