Abstract:Purpose Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied. Design/methodology/approach COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand. Findings The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand. Originality/value The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

Investigation on the Temperature Distribution Uniformity of an Extrusion-Based 3D Print Head and Its Temperature Control Strategy

Investigation on the Temperature Control Accuracy of a Print Head for Extrusion 3D Printing and Its Improved Design.

Investigation of the Temperature Gradient Control in the Printing Space for the Material Extrusion of Medical Biodegradable Hydrogel.

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

A Systematic Thermal Analysis for Accurately Predicting the Extrusion Printability of Alginate-Gelatin-Based Hydrogel Bioinks

Research on Internal Filling Technology of 3D Printing PEEK

Structural design and heat transfer analysis of twin-screw extrusion 3D printer

Study on the Temperature Field Distribution of the Interface and Process Parameter Optimization for Material Extrusion of PLA

Experimental and numerical investigations on heat transfer in fused filament fabrication 3D-printed specimens

Temperature-compensated Constitutive Model of Fused Filament Fabrication 3D Printed PLA Materials with Full Extrusion Temperatures

Design and Optimization of Heat Dissipation and Cooling Device for the Open 3D Printer

Investigating gradient temperature control for enhanced interfacial bonding behavior in material extrusion 3D printing continuous fiber reinforced polymer composites

Stabilization of Filament Production Rate for Screw Extrusion-Based Polymer 3D-Printing

The Effect of Heterogeneous Geometry on Steady-State Heat Transfer in Extrusion-Based 3D Printed Structures

Numerical Simulation of 3D Concrete Printing Derived from Printer Head and Printing Process

Experimental Investigation and Numerical Simulations of Temperature and Morphology in Material Extrusion Additive Manufacturing

Temperature Analyses in Fused Filament Fabrication: From Filament Entering the Hot-End to the Printed Parts

Simulation of temperature profile in fused filament fabrication 3D printing method

Heat Accumulation Effect in Metal Droplet-based 3D Printing: Evolution Mechanism and Elimination Strategy

A Process Parameter Design Method for Improving the Filament Diameter Accuracy of Extrusion 3D Printing

Influence of Fused Deposition Modelling Nozzle Temperature on the Rheology and Mechanical Properties of 3D Printed β-Tricalcium Phosphate (TCP)/Polylactic Acid (PLA) Composite