Abstract:Recent investigations of Field Programmable Gate Array (FPGA)-based time-to-digital converters (TDCs) have predominantly focused on improving the time resolution of the device. However, the monolithic integration of multi-channel TDCs and the achievement of high measurement throughput remain challenging issues for certain applications. In this paper, the potential of the resources provided by the Kintex-7 Xilinx FPGA is fully explored, and a new design is proposed for the implementation of a high performance multi-channel TDC system on this FPGA. Using the tapped-delay-line wave union TDC architecture, in which a negative pulse is triggered by the hit signal propagating along the carry chain, two time measurements are performed in a single carry chain within one clock cycle. The differential non-linearity and time resolution can be significantly improved by realigning the bins. The on-line calibration and on-line updating of the calibration table reduce the influence of variations of environmental conditions. The logic resources of the 6-input look-up tables in the FPGA are employed for hit signal edge detection and bubble-proof encoding, thereby allowing the TDC system to operate at the maximum allowable clock rate of the FPGA and to achieve the maximum possible measurement throughput. This resource-efficient design, in combination with a modular implementation, makes the integration of multiple channels in one FPGA practicable. Using our design, a 128-channel TDC with a dead time of 1.47 ns, a dynamic range of 360 ns, and a root-mean-square resolution of less than 10 ps was implemented in a single Kintex-7 device.

A Bin-by-Bin Calibration with Neural Network for FPGA-Based Tapped-Delay-Line Time-to-Digital Converter

A Nonlinearity Minimization-Oriented Resource-Saving Time-to-Digital Converter Implemented in a 28 Nm Xilinx FPGA

A 19 ps Precision and 170 M Samples/s Time-to-Digital Converter Implemented in FPGA with Online Calibration

A 20-ps temperature compensated Time-to-Digital Converter (TDC) implemented in FPGA

A 20-Ps Time-to-Digital Converter (TDC) Implemented in Field-Programmable Gate Array (FPGA) with Automatic Temperature Correction

A 1.15-Ps Bin Size and 3.5-Ps Single-Shot Precision Time-to-Digital Converter with On-Board Offset Correction in an FPGA

Tapped delay line for compact time-to-digital converter on UltraScale FPGA and its coding method

A 16-Channel 15 Ps TDC Implemented in a 65 Nm FPGA

A Multi-Chain Merged Tapped Delay Line for High Precision Time-to-Digital Converters in FPGAs

A High Resolution Time-to-digital-convertor Based on a Carry-Chain and DSP48E1 Adders in a 28-Nm Field-Programmable-gate-array

A 3.9 Ps Time-Interval RMS Precision Time-to-Digital Converter Using a Dual-Sampling Method in an UltraScale FPGA

A Fully Fledged TDC Implemented in Field-Programmable Gate Arrays

A Vernier Caliper Time-to-Digital Converters with Ultralow Nonlinearity in FPGAs

A Low Dead Time Vernier Delay Line TDC Implemented in an Actel Flash-Based FPGA

A High-Linearity Vernier Time-to-Digital Converter on FPGAs With Improved Resolution Using Bidirectional-Operating Vernier Delay Lines

A 1.7 Ps Equivalent Bin Size and 4.2 Ps RMS FPGA TDC Based on Multichain Measurements Averaging Method

A High Precision Time-to-Digital Converter based on Multi-chain Interpolation with a Low Cost Artix-7 FPGA

Design and Implementation of High-Precision Timing Module for NR Terminals Based on FPGA

A time-to-digital converter with steady calibration through single-photon detection

A 128-Channel, 710 M Samples/Second, and Less Than 10 Ps RMS Resolution Time-to-Digital Converter Implemented in a Kintex-7 FPGA

High-Speed and Time-Interleaved ADCs Using Additive-Neural-Network-Based Calibration for Nonlinear Amplitude and Phase Distortion