Abstract:During the production of fiber-reinforced plastics using resin transfer molding (RTM), various characteristic defects and flaws can occur, such as fiber displacement and fiber waviness. Particularly in high-pressure RTM (HP-RTM), fiber misalignments are generated during infiltration by local peaks in the flow rate, leading to a significant reduction in the mechanical properties. To minimize or avoid this effect, the manufacturing process must be well controlled. Simulative approaches allow for a basic design of the mold filling process; however, due to the high number of influencing variables, the real behavior cannot be exactly reproduced. The focus of this work is on flow front monitoring in an HP-RTM mold using phased array ultrasonic testing. By using an established non-destructive testing instrument, the effort required for integration into the manufacturing process can be significantly reduced. For this purpose, investigations were carried out during the production of test specimens composed of glass fiber-reinforced polyurethane resin. Specifically, a phased array ultrasonic probe was used to record individual line scans over the form filling time. Taking into account the specifications of the probe used in these experiments, an area of 48.45 mm was inspected with a spatial resolution of 0.85 mm derived from the pitch. Due to the aperture that had to be applied to improve the signal-to-noise ratio, an averaging of the measured values similar to a moving average over a window of 6.8 mm had to be considered. By varying the orientation of the phased array probe and therefore the orientation of the line scans, it is possible to determine the local flow velocities of the matrix system during mold filling. Furthermore, process simulation studies with locally varying fiber volume contents were carried out. Despite the locally limited measuring range of the monitoring method presented, conclusions about the global flow behavior in a large mold can be drawn by comparing the experimentally determined results with the process simulation studies. The agreement between the measurement and simulation was thus improved by around 70%.

Monitoring of Three-Dimensional Resin Flow Front Using Hybrid Piezoelectric-Fiber Sensor Network in a Liquid Composite Molding Process

In-situ monitoring of liquid composite molding process using piezoelectric sensor network

Life-Cycle Monitoring of CFRP using Piezoelectric Sensors Network

Life-cycle health monitoring of composite structures using piezoelectric sensor network

Real-Time Life-Cycle Monitoring of Composite Structures Using Piezoelectric-Fiber Hybrid Sensor Network

Sensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding

Monitoring the resin infusion manufacturing process under industrial environment using distributed sensors

Embedding Piezoresistive Pressure Sensors to Obtain Online Pressure Profiles Inside Fiber Composite Laminates

A neural-network-assisted method for flow-front estimation in resin transfer molding using pressure sensors

Leaky Lamb wave–based resin impregnation monitoring with noninvasive and integrated piezoelectric sensor network

Self-Sensing Of Position-Related Loads In Continuous Carbon Fibers-Embedded 3d-Printed Polymer Structures Using Electrical Resistance Measurement

Weak Fiber Bragg Grating Array-Based In Situ Flow and Defects Monitoring During the Vacuum-Assisted Resin Infusion Process

Real-time self-monitoring and smart bend recognizing of fiber-reinforced polymer composites enabled by embedded magnetic fibers

Flow Front Monitoring in High-Pressure Resin Transfer Molding Using Phased Array Ultrasonic Testing to Optimize Mold Filling Simulations

Integrated self-monitoring and self-healing continuous carbon fiber reinforced thermoplastic structures using dual-material three-dimensional printing technology

Magnetic Fiber Enabled Curing Electrogram: Real-time Process Monitoring for Thermosetting Polymer Materials

Embedded Pt-PVDF sensor without compromising mechanical properties of GFRP for on-line sensing

Smart Adhesive Joint with High-Definition Fiber-Optic Sensing for Automotive Applications

Large-scale deformation and damage detection of 3D printed continuous carbon fiber reinforced polymer-matrix composite structures

Real-time in-situ process monitoring method based on the self-conductivity of carbon fiber prepreg for automated fiber placement (AFP)

An Optical Fiber Sensor Monitoring on Resin Flow