Abstract:To prevent the steam from channeling and breakthrough in heterogeneous oil sands reservoirs, oil-in-water (O/W) emulsion is proposed and developed as a plugging agent in this study. However, one suspects that increased temperature destabilizes emulsion, promoting oil/water separation and thus to lose its plugging benefits induced by "Jamin effect". This intuitive picture changes when the emulsion flows through heated porous media. In this paper, we show that increasing temperature enhances emulsion plugging effect, after a critical temperature reaches. O/W emulsions were firstly prepared at room temperature (similar to 20 degrees C) individually using eight different surfactants and then injected in sandpacks at temperatures ranging from 20 degrees C to 140 degrees C. Experimental results show that the emulsion plugging strength at temperature of 140 degrees C is three times greater than that at mom temperature (20 degrees C) and still shows a rising trend with temperature up to 140 degrees C. Measurements of the median droplet sizes of the effluents at different temperatures showed that there was no phase separation during the flow tests. This is because that the "snap-off' and "fingering induced break-up" processes keep the emulsion droplets dynamically stable during the flowing process. It is the changing hydrophilic-lipophilic characteristic of the surfactant molecules, as the temperature increases, that causes a parabola trend with a minimum of IFT and thus influences the emulsion plugging effect. What we expect following steam injection into the reservoir is that the achieved emulsion plugging strength could still be maintained or even enhanced so that the emulsion slug will not be easily displaced away by further steam injection, thus optimizing thermal recovery performance. By carefully selecting surfactant on the basis of its hydrophilic-lipophilic characteristic, an optimum emulsion system, contributing expected plugging strength at elevated temperatures, was designed, applied and verified for effective conformance control in heterogeneous parallel-sandpack. The experimental results demonstrate the designed emulsion can achieve conformance control in parallel-sandpack with a permeability ratio of 10 Darcy: 5 Darcy at room temperature and the conformance performance is still maintained as the temperature increases, up to 99 degrees C.

Toward an Improved Understanding of Emulsion Stabilization at Elevated Temperatures by Direct Visualization and Reversibility Analysis

Mechanism of High Stability of Water-in-Oil Emulsions at High Temperature

Interfacial Cooperative Assembly of Surfactants and Opposite Wettability Nanoparticles Stabilizes Water-in-Oil Emulsions at High Temperature

A novel formulation of the pickering emulsion stabilized with silica nanoparticles and its thermal resistance at high temperatures

Insights into the Thermal Responsiveness of W/O Emulsions with Nanoparticles and Oleogels As Building Blocks

Probing the interactions between asphaltenes and a PEO-PPO demulsifier at oil-water interface: Effect of temperature

Emulsion-assisted Thermal Recovery Method in Heterogeneous Oilsands Reservoir

High-temperature stability and fcc reaction property of emulsified heavy oil

Pickering Emulsion Stabilized by Organoclay and Intermediately Hydrophobic Nanosilica for High-Temperature Conditions

Influence of the Interfacial Properties on the Stability of Water in Heavy Oil Emulsions in Thermal Recovery Process

Effects of Asphaltene Concentration and Test Temperature on the Stability of Water-in-Model Waxy Crude Oil Emulsions

Rheological Study on the Invert Emulsion Fluids with Organoclay at High Aged Temperatures

Altering Emulsion Stability with Heterogeneous Surface Wettability

Influence of Hydrophobicity Distribution of Particle Mixtures on Emulsion Stabilization.

Temperature-responsive salt-resistant poly(sulfobetaine methacrylate)-based emulsifiers for heavy oils

Demulsification of Asphaltenes and Resins Stabilized Emulsions Via the Freeze/Thaw Method

Inhibition of Heat-Induced Flocculation of Myosin-Based Emulsions Through Steric Repulsion by Conformational Adaptation-Enhanced Interfacial Protein with an Alkaline Ph-Shifting-driven Method.

Well-Defined Temperature-Sensitive Surfactants for Controlled Emulsion Coalescence

Interfacial Crystallized Oleogel Emulsion with Improved Freeze-Thaw Stability and Tribological Properties: Influence of Cooling Rate

Highly Stable Concentrated Nanoemulsions by the Phase Inversion Composition Method at Elevated Temperature

The investigation of thermal stability and GC-MS analysis of Acorus tatarinowii and Atractylodes lancea volatile oils treated by β cyclodextrin inclusion and Pickering emulsion technologies