Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

Interfacial characterization and reaction mechanism of Ti/Al multi-material structure during laser powder bed fusion process

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Additive manufacturing of Ti–6Al–4V/Al–Cu–Mg multi-material structures with a Cu interlayer

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

Fabrication of Ti3Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture

High power laser powder bed fusion of Ti6Al4V alloy: The control of defects, microstructure, and mechanical properties

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy

Multi-laser Powder Bed Fusion of Ti–6Al–4V Alloy: Defect, Microstructure, and Mechanical Property of Overlap Region

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

Abstracts from the Bone and Tooth Society Annual Meeting 2001

Multi-material additive manufacturing of a bio-inspired layered ceramic/metal structure: Formation mechanisms and mechanical properties

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

Microstructure and mechanical properties of TiB 2 /Al-5Cu composites fabricated by multi-material laser powder bed fusion

Formability and microstructure of laser powder bed fused AlSi10Mg alloy sheets under various deformation conditions

The effect of process parameters on the stability and efficiency in the laser powder bed fusion of Ti-6Al-4 V based on the interval powder layer thickness

Solidification microstructure variations in additively manufactured Ti-6Al-4V using laser powder bed fusion

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

Enhanced strength-ductility synergy and mechanisms of heterostructured Ti6Al4V-Cu alloys produced by laser powder bed fusion