Abstract:The insufficient adhesive strength of Physical Vapor Deposition (PVD) coatings is still the key issue that needs to be solved urgently for high-efficiency and high-quality difficult-to-machine materials cutting processing. Currently, laser micromachining is extensively utilized to fabricate micro-textures on the substrate to enhance coatings adhesion. However, laser ablation will cause irregular protrusions inside and on the edges of the textures, which could influence the quality of deposited coatings. Therefore, micro-textures were fabricated on the substrate by an ion beam (IBE)/laser machining method, and the influence of IBE/laser textures on the adhesive strength of PVD coatings is revealed. Firstly, a micro-pits array was prepared on WC/Co substrates with different machining parameters, such as laser repetition frequency and ion beam etching time. The micro-topography and mechanical properties of the substrates with different pretreatments were studied. Then, cathode arc-evaporation technique was utilized to deposit AlCrN film on the IBE/laser textured substrates. The scratch test and dry machining experiments of AISI 316L stainless steel were performed to evaluate the adhesive strength and machining performance of the coated samples with various pretreated substrates. The results demonstrate that laser texturing and ion beam etching both enhanced the coatings adhesion. Therefore, the critical load of the coatings deposited on the IBE/laser textured substrates with 25 kHz laser repetition frequency and 150 min etching time (FN, C2 = 3.39 N) exhibited the highest value, which was 19.4 % higher than that of the conventional AlCrN samples (FN, C2 = 2.84 N). Moreover, the cutting forces FX, FY, FZ and the friction coefficient of IBE/laser textured coated tool were decreased by 18.7 %, 20.6 %, 10.2 % and 16.7 % compared with that of conventional coated tool at the high cutting speed of 200 m/min. Finally, the possible mechanisms of IBE/laser texturing pretreatment on enhancing PVD coatings adhesion were discussed.

Enhancing Adhesion Strength of PVD AlCrN Coating by Novel Volcano-Shaped Micro-Textures: Experimental Study and Mechanism Insight

Adhesion and machining performance of PVD AlCrN coatings with an ion beam/laser textured substrate

Investigation of mountainous laser texturing for improving the adhesion and tribological properties of AlCrN coatings

Controllable preparation of micro-textures on WC/Co substrate surface by an integrated laser-dry etching process for improving PVD coatings adhesion

Study on the surface performance strengthening of AlCrN coated cemented carbide by micro-texture laser preparation process

High-temperature tribological properties of AlCrN coatings deposited on textured surfaces under dry friction

Analysis of Wear Vibration Behavior of Micro-Textured Coated Cemented Carbide Considering High-Order Scale

Study on the substrate surface micro-texturing/carburizing regulating the film-substrate adhesion and wear behavior of DLC coatings

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Laser-induced concave/convex micro-textures array for enhancing performance of surface coatings: Bond coating in thermal barrier coating system

Surface integrity of machined AISI D2 steel and its effect on the adhesion of a PVD-AlCrN coating

Study on surface properties of coated WC-Co alloy based on laser reduction process

Effects of texture spacing and bulges of bionic sinusoidal texture on the adhesion properties and fracture mechanism of plasma-sprayed coatings

Enhancing the adhesion strength and wear resistance of nanostructured NiCrN coatings

Investigation of the Dislocation Density of NiCr Coatings Prepared Using PVD–LMM Technology

Fabrication and tribological properties of textured diamond coatings on WC-Co cemented carbide surfaces

Fabrication of AlTiN coatings deposited on the ultrasonic rolling textured substrates for improving coatings adhesion strength

On crack evolution with texturization of bonding layer in thermal barrier coating

The effect of substrate surface integrity on the surface properties of TiCrN coating applied via the CAE‐PVD method

Improved Interfacial Adhesion Between TiAlN/DLC Multi-Layered Coatings by Controlling the Morphology Via Bias

Fabrication of TiN Coatings Deposited on Laser Shock Micro-Textured Substrates for Improving the Interface Adhesion Properties of Coatings