Abstract:Welding residual stress (WRS) significantly influences the fatigue life and safety of welded steel structures. Post-weld heat treatment (PWHT) is a common method employed to mitigate WRS. In present study, the WRS evolution law and relaxation mechanism of U-rib-to-deck joints was investigated during PWHT. High-temperature heat treatment tests with varying holding times were conducted on U-rib-to-deck joints to reduce WRS. The WRS distributions were measured using the hole-drilling method before and after PWHT. ABAQUS software, incorporating the Norton-Bailey creep constitutive model, was employed to simulate the WRS evaluation during both welding and PWHT processes. The simulated values were validated against the measured data, and the effects of different holding times, holding temperatures, and heating and cooling rates during PWHT on WRS relaxation were discussed. The results demonstrate that PWHT effectively reduces WRS and leads to a more uniform distribution. Extending the PWHT holding time from 0.5 h to 1 h and 2 h results in a gradual decrease in WRS relaxation at 600 °C, primarily occurring in the high-value stress region of the weld zone with a small amplitude. Elevating the PWHT temperature from 500 °C to 550 °C and subsequently to 600 °C amplifies the significance of WRS relaxation. Variations in heating and cooling rates (200 °C/h and 80 °C/h, 100 °C/h and 40 °C/h, 50 °C/h and 20 °C/h) lead to a gradual decrease in WRS relaxation across the entire model. Furthermore, considering the creep effect, the stress relaxation rate in the weld is approximately 70 %–80 %, which found to be about 2–3 times higher than that without considering the creep effect. By understanding the evolution law and relaxation mechanism, this study provides valuable insights for designing PWHT processes and assessing their impact on structural safety and fatigue life.

The Effect of Oscillating Capping TIG Welding on Residual Stresses of 2219-T8 Butt Joint

Effects of the Number of Welding Passes on Microstructure and Properties of 2219-C10S Aluminum Alloy TIG-Welded Joints

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Influence of restraint conditions on residual stress and distortion of 2219-T8 aluminum alloy TIG welded joints based on contour method

On the Mechanism of Residual Stresses Relaxation in Welded Joints under Cyclic Loading

"Anneal" softening effect of 2219-T8 aluminum alloy joint during welding and its influence on prediction of welding residual stresses

Tensile properties of TIG welded 2219-T8 aluminum alloy joints in consideration of residual stress releasing and specimen size

Effects of Weld Reinforcement on Tensile Behavior and Mechanical Properties of 2219-T87 Aluminum Alloy TIG Welded Joints

Numerical Simulations of Welding Residual Stresses in VPTIG-welded Joints of the 2219 Aluminum Alloy

Numerical Study on Welding Residual Stress Distribution of Corrugated Steel Webs

Effect of Tool Traverse Speed on Joint Line Remnant and Mechanical Properties of Friction Stir Welded 2195-T8 Al–Li Alloy Joints

Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

Effect of welding residual stress on the performance of CFST tubular joints

Study on the Inconsistency in Mechanical Properties of 2219 Aluminium Alloy TIG-welded Joints

Experimental and Numerical Simulation to Study the Reduction of Welding Residual Stress by Ultrasonic Impact Treatment

Effect of Solid-State Phase Transformation and Transverse Restraint on Residual Stress Distribution in Laser–Arc Hybrid Welding Joint of Q345 Steel

Influence of post-weld heat treatment on welding residual stress in U-rib-to-deck joint

PWHT influence on welding residual stress in 45 mm bridge steel butt-welded joint

Effects of welding residual stresses on fatigue reliability assessment of a PC beam bridge with corrugated steel webs under dynamic vehicle loading

Effects of Welding Parameters on Weld Shape and Residual Stresses in Electron Beam Welded Ti2AlNb Alloy Joints

Effect of beam oscillation on microstructure and properties of laser-TIG hybrid welding of D406A ultra-high strength steel