Abstract:Introduction: A bio-implant is a drug-delivery system that is implanted in the human body for a period of more than 30 days. Electromechanical systems are one type of bio-implant that has recently been introduced as a new generation of targeted drug delivery methods. The overarching goal of utilizing these systems is to integrate electrical and mechanical features in order to benefit from the numerous applications of these two systems when used together. The current study aimed to design a prototype of an electromechanical system using Fused Deposition Modeling (FDM), Selective Laser Sintering (SLS), and MultiJet Fusion (MJF) techniques for drug delivery that can release a specific drug dosage in the patient's body by connecting to a sensor or under the control of a signal sent by the physician. Methods: Initially, the implant chambers were created in the form of a hollow cylinder, closed at one end, using three different types of 3D printers: FDM, SLS, and MJF. Each implant was then filled with a model drug (pentoxifylline) and sealed with a thin gold membrane. To achieve the lowest voltage required to melt the gold membrane, an electric circuit with controllable DC voltage generator was designed. Finally, the mechanical resistance, drug release rate, and surface morphology of the designed implants were evaluated. Results: The MJF 3D printer, overally, had higher printing precision and repeatability than other printers; however, the implants printed by the FDM 3D printer were more accurate than other techniques (P value < 0.001), similar to the dimensions of the designed file. The mechanical resistance of the implants was also evaluated, and the polylactic acid implants printed by FDM had the highest value of Young's modulus in both the standard samples and the designed implants. During the 3-month drug leakage study, FDM 3D printed implant had a greater ability to store the desired drug load (P value < 0.001), Furthermore, the SEM micrographs revealed that the polylactic acid implants printed by FDM had minimal porosity in their structure and the layers were well adhered together. The gold membrane with a middle diameter of 2 mm required the lowest voltage of 6 V. As a result, the final electrical circuit was designed with smaller dimensions in order to achieve the voltage required to melt the gold membrane. Conclusion: Due to the lack of drug leakage and other mechanical studies, the electromechanical implant produced by the FDM 3D printer was chosen as the optimal electromechanical implant in this study. Along with the designed small circuit, this implant can release a drug dosage in the patient's body at the physician's demand.

A 3D-printed Microfluidic Valve for Implantable Drug Delivery

Configurable 3D Printed Microfluidic Multiport Valves with Axial Compression

Fabrication of Micro Pneumatic Valves with Double-Layer Elastic Poly(dimethylsiloxane) Membranes in Rigid Poly(methyl Methacrylate) Microfluidic Chips

Reasearch and fabrication of integrated pneumatic microvalves in polymer microfluidic chip

Thermally-actuated microfluidic membrane valve for point-of-care applications

3D printed microfluidic valve on PCB for flow control applications using liquid metal

Programmed Internal Reconfigurations in a 3D-Printed Auxetic Metamaterial Enable Fluidic Control for a Vertically Stacked Valve Array

Programmed Internal Reconfigurations in a 3D-Printed Mechanical Metamaterial Enable Fluidic Control for a Vertically Stacked Valve Array

Fabrication and characterization of hydrogel-based microvalves

Developments of 3D Printing Microfluidics and Applications in Chemistry and Biology: a Review

"Catastrophic antiphospholipid syndrome crisis".

Prototyping sutureless shape-memory valve stent via integrated 3D printing

Diffusion-free valve for preprogrammed immunoassay with capillary microfluidics

Fabrication and simulation of a microvalve for molecular communication control on a chip

Characterization and evaluation of 3D printed microfluidic chip for cell processing

A Wirelessly Controlled Scalable 3D-Printed Microsystem for Drug Delivery

3D Printed Lego®-like Modular Microfluidic Devices Based on Capillary Driving.

Design and preparation of an electromechanical implant prototype for an on-demand drug delivery

Bonding-Free Capillary Microfluidics via a 3D-Printed Railed Microchannel

Microfluidic bioprinting of tough hydrogel-based vascular conduits for functional blood vessels

Multi-Resin Masked Stereolithography (MSLA) 3D Printing for Rapid and Inexpensive Prototyping of Microfluidic Chips with Integrated Functional Components