Abstract:Microstructural features play a major role in strain distribution and TRIP effect, influencing the plastic deformation behavior of multiphase steel. In this work, the bainitic multiphase microstructure with or without pre-formed martensite (PM) was obtained by the below-M S and above-M S austempering process. The evolution of strain partitioning and TRIP effect on plastic deformation were studied by combining micro digital image correlation (μ-DIC) analysis with in-situ tensile test in the multiphase microstructure. The changes of microstructure during deformation were systematically investigated by various characterization methods. The results show that the regions of strong strain partitioning in multiphase microstructure are different. Compared with the above-M S austempered sample without PM, the strain partitioning of the below-M S austempered sample containing PM is concentrated in the pre-formed martensite region while not in the blocky retained austenite (RA) region. The strain concentration in the PM region of the below-M S austempered sample is smaller than that in the blocky RA region of the above-M S austempered sample at the same engineering strain. The PM shares the stress load on RA during plastic deformation, thus can coordinate microstructure deformation and delay the early occurrence of the TRIP effect of the below-M S austempered sample. Moreover, the introduction of PM in the below-M S austempered sample increases the mechanical stability of RA, which is beneficial to produce an effective TRIP effect and delay necking to high strain. Consequently, the plasticity of the medium-carbon bainitic multiphase steel containing PM is enhanced by the effective TRIP effect and uniform strain partitioning.

In-situ investigation of composition segregation and deformation streamline in bainitic steel on mechanical properties

Microstructures-based Constitutive Analysis for Mechanical Properties of Gradient-Nanostructured 304 Stainless Steels

In-situ Deformation Characterization of Mesosegregated High-Strength Low-Alloy Steel

In-situ Observation of Tensile Deformation and Retained Austenite Transformation Behaviors in Carbide-Free Bainitic Steel

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Effect of Solidification Segregation on Microstructure and Mechanical Properties of a Ni-Cr-Mo-V Steel Weld Metal

Insights into the Strain Rate on Microstructure Evolution of Carbide‐Free Bainitic Steel

Study on Uniaxial Tensile Deformation of Bainite/ferrite Dual Phase Steel

Effect of Cr/Mn segregation on pearlite—martensite banded structure of high carbon bearing steel

Revealing the evolution mechanism from spot segregation to banded defect above the austenitization temperature

Tensile Deformation Behavior of High Strength Anti-Seismic Steel with Multi-Phase Microstructure

Effect of austenite deformation on bainite microstructure and mechanical properties of low carbon Si-Mn steel

Dendrite Structure, Spot Segregation and Banded Defect of Gear Steel in Continuous Casting and Rolling Process

Micro Plastic Deformation Behavior Of Carbide-Free Bainitic Steel During Tensile Deformation Process

Roles of pre-formed martensite in deformation behavior and strain partitioning of medium-carbon bainitic steel by quasi-in-situ tensile tests

In Situ Observation of Bainitic Transformation Behavior in Medium Carbon Bainitic Steel

Microstructure Evolution In A Low Carbon Nb-Ti Microalloyed Steel

EFFECT OF MARTENSITE DISTRIBUTION ON MICROSCOPIC DEFORMATION BEHAVIOR AND MECHANICAL PROPERTIES OF DUAL PHASE STEELS

Microstructure Evolutions During Multi-pass Hot Deformation and Mechanical Properties of Al-Si Bearing Low Carbon Steel

Ex situ analysis of high-strength quenched and micro-alloyed steel during austenitising bending process: numerical simulation and experimental investigation

Quasi-Situ Characterization of Retained Austenite Orientation in Quenching and Partitioning Steel via Uniaxial Tensile Tests