Abstract:Phase-transformations and microstructural evolution during and after inter-critical annealing of a low-alloy, dual-phase steel are studied utilizing dilatometric measurements, and microstructural characterization methods, including scanning electron microscopy, synchrotron X-ray diffraction, and atom-probe tomography. Dilatometric measurements reveal that the sample contains ~72% austenite, after annealing for 5-min at 871 oC, which agrees with the water-quenched microstructure, and ~90% after further annealing to 1 h, which agrees with thermodynamic predictions. A continuous-cooling transformation (CCT) diagram is constructed, within the cooling-rate range between 1 oC/s and 70 oC/s. The incubation time for the ferrite-transformation is <1 s, after inter-critical annealing, and the secondary-phases are mainly pearlite for cooling-rates of <5 oC/s, and martensite for cooling-rates >10 oC/s, which is confirmed utilizing scanning electron-microscope observations. The microhardness increases as the cooling rate increases, and an abrupt slope-change is explained by the major secondary-phase changing from martensite to pearlite between 5 oC/s and 10 oC/s. Atom-probe tomography demonstrates the coexistence of martensite and pearlite as secondary-phases for 30 oC/s and a switch in austenite-ferrite transformation mechanisms from para-equilibrium (70 oC/s) to partitioning local-equilibrium (30 oC/s). A microstructural map is constructed to reveal the austenite decomposition products in the cooling-rate range between 1 oC/s and 70 oC/s. Based on composition measurements of the matrix, utilizing APT, the effects of cooling-rates on solid-solution-strengthening are estimated, and the results demonstrate that solid-solution strengthening, especially carbon-redistribution, accounts for the majority of the strength variations due to different cooling-rates. (239 words)

EFFECT OF MARTENSITE DISTRIBUTION ON MICROSCOPIC DEFORMATION BEHAVIOR AND MECHANICAL PROPERTIES OF DUAL PHASE STEELS

Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

Effects of martensite particle size and spatial distribution on work hardening behaviour of fine-grained dual-phase steel

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction

Mechanical properties and deformation mechanisms of a novel austenite-martensite dual phase steel

Effect of annealing temperature on microstructure and properties of a dual phase steel

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

Roles of pre-formed martensite in deformation behavior and strain partitioning of medium-carbon bainitic steel by quasi-in-situ tensile tests

Element Partitioning Effect on Microstructure and Mechanical Property of the Micro-Laminated Fe–Mn–Al–C Dual Phase Steel

Fracture Mode of Martensite-Austenite Constituents Containing Multiphase Steel Controlled by Microstructural and Micromechanical Aspects

Effect of Annealing Process on Microstructure, Texture, and Mechanical Properties of a Fe-Si-Cr-Mo-C Deep Drawing Dual-Phase Steel

Effect of holding time on the microstructure and mechanical properties of dual-phase steel during intercritical annealing

Martensite size and morphology influence on strain distribution and micro-damage evolution in dual-phase steels; comparing segregation-neutralised and banded grades

Microstructure Regulation and Mechanical Properties of Low-Carbon Multiphase Steels

[Electrophoretic and histochemical research on glycoproteins of the corneal epithelium and endothelium].

Effect of Intercritical Annealing Time on Microstructure Evolution and Mechanical Properties of Low Carbon Medium Manganese Steel Subjected to Multi-Step Heat Treatment Process

Strength–Ductility Trade-Off in Dual-Phase Steel Tailored via Controlled Phase Transformation

Effect of Coiling Temperature on Microstructure and Properties of Ferritic-Bainitic Dual-Phase Steels

Quasi-Situ Characterization of Retained Austenite Orientation in Quenching and Partitioning Steel via Uniaxial Tensile Tests

Semi in-situ investigations on deformation-induced micro-damage in high-strength dual-phase steels

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel