Abstract:The unique features of DLC coatings in providing low friction and low wear and, at the same time, causing low wear to the counterface make them very attractive in industrial applications, in improving tribological performance of mechanical components on various substrates. In this study, composite DLC coatings have been deposited on sintered ferrous alloy, M42 tool steel, 2618 aluminium alloy, and 6063 aluminium extrusion substrates using the combined CFUBMS-PACVD technique. The effect of mechanical properties of substrate materials on tribological behaviour of the composite DLC coatings has been investigated at various loads on a ball-on-disk wear machine in dry air. A transition load was usually observed for coatings on the various substrates except for the aluminium extrusion; above the transition load the coating was completely destroyed via some spallation/fragmentation process after 2 h sliding, and the wear rate increased dramatically with further increase in load. The coating system on sintered ferrous alloy substrate exhibited the highest transition load among the four types of substrates studied. This is considered to have resulted from the combined effects of the lower elastic modulus of the porous sintered ferrous alloy substrate, which decreases the stress concentrations in the contact region, and the surface roughness and porosity, which enhance the bonding strength between the coating and the substrate under multi-contact conditions. The high elastic modulus of the tool steel substrate leads to tensile stress conditions in the sliding contact region and therefore makes coatings deposited on such a substrate more prone to breakdown/fragmentation, resulting in a transition load close to that for coatings on the soft 2618 aluminium alloy substrate. For coatings on the 6063 aluminium extrusion substrate, significant plastic deformation occurred in the substrate at loads above 1.5 N. However, despite the heavy deformation in the substrate, coatings on this substrate were not scraped off, as were coatings on the 2618 aluminium alloy substrate, even at a load as high as 20 N. The specific wear rate increased continuously with load, no apparent transition load being explicitly identifiable. This study shows that hard DLC coatings can be applied on both hard and soft substrates for improvement of the tribological behaviour of mechanical components. (C) 1997 Elsevier Science Ltd.

The Role of Cermet Interlayer on Tribological Behaviors of DLC/Cr3C2–NiCr Duplex Coating from the Perspective of Carbonaceous Transfer Film Formation

Role of carbide content in governing the mechanical and tribological properties of DLC/Cr 3 C 2 –NiCr duplex coatings

Role of Carbide Content in Governing the Mechanical and Tribological Properties of DLC/Cr3C2–NiCr Duplex Coatings

Friction and Wear Properties of Ni-P/Ti/DLC Multilayer Films

Sliding friction behaviors of TiCN/Cr3C2-NiCr and TiCN/WC-CoCr duplex coatings fabricated by combining HVOF and HT-CVD procedures

Sliding friction behaviors of TiCN/Cr 3 C 2 -NiCr and TiCN/WC-CoCr duplex coatings fabricated by combining HVOF and HT-CVD procedures

Mechanical and High-Temperature Tribological Properties of Cr3C2-NiCr/TiN Duplex Coating

Influence of multi-interfacial structure on mechanical and tribological properties of TiSiN/Ag multilayer coatings

The Effect of Carbon Structure of DLC Coatings on Friction Characteristics of MoDTC-Derived Tribofilm by Using an In Situ Reflectance Spectroscopy

Probing Tribological Behaviors of Cr-DLC in Corrosion Solution by Tailoring Sliding Interface

Effects of high-velocity oxygen fuel metal-ceramic interlayer on the mechanical and tribological properties of Si/DLC-coated Ti-6Al-4V alloy

Tribological performance of DLC-coated ceramics against cemented carbide under dry sliding conditions

Effects of Intermediate Layers on the Tribological Behavior of DLC Coated 2024 Aluminum Alloy

Study on the Deposition and Tribological Properties of Diamond/dlc Composite Coating on WC-Co Substrate

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

AlCrN/Cr3C2–NiCr duplex coating towards high load-bearing and dry sliding antiwear applications

Tribological Performance of DLC Coating under Aqueous Solutions

Tribological behavior of diamond-like carbon in-situ formed on Fe3C-containing carburized layer by plasma carburizing

The effect of substrate properties on tribological behaviour of composite DLC coatings

Enhanced tribological and corrosion properties of DLC/CrN multilayer films deposited by HPPMS

Investigation of Mechanical and Tribological Properties of Super-Thick DLC Films with Different Modulation Ratios Prepared by PECVD