Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Development and Verification of a Reduced Dimethoxymethane/n-Heptane/toluene Kinetic Mechanism and Modelling for CI Engines

Comparison of Kinetic Mechanisms for Numerical Simulation of Methanol Combustion in DICI Heavy-Duty Engine

Development and Verification of Simplified Methane/dimethyl Ether Mechanism for Micro-Combustion

Development and Validation of a Reduced Multi-Component Mechanism for Diesel Engine Application

Study on Reduced Chemical Kinetic Model for DME HCCI Combustion

A Comprehensive Experimental and Kinetic Modeling Study of Dimethoxymethane Combustion

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Development and Validation of a New Reduced Diesel/natural Gas Mechanism under Engine-Relevant Conditions

A Reduced Combustion Kinetic Model for the Methanol-Gasoline Blended Fuels on SI Engines

A Novel Reduced Reaction Mechanism for Diesel/2,5-Dimethylfuran Engine Application

Development and Validation of a Reduced MF/biodiesel Mechanism for Diesel Engine Application

Development of a Combined Reduced Primary Reference Fuel-Alcohols (Methanol/ethanol/propanols/butanols/n-Pentanol) Mechanism for Engine Applications

Development and Validation of a Reduced N-Heptane/Toluene/DMF-PAH Mechanism for Diesel Engine Application

Development of a reduced n-heptane/toluene/tetrahydrofuran mechanism for dual-fuel engine combustion prediction

Development of a Diesel/Natural Gas Mechanism Model for the CFD Simulation of Dual-Fuel Engine.

Development and Validation of a Reduced Toluene/N-Heptane/N-Butanol Mechanism for Combustion and Emission Prediction in IC Engine

Mechanism Analysis on Controllable Methanol Quick Combustion

Development and validation of a reduced chemical kinetic model for dimethyl ether combustion

A Multi-Component Surrogate Mechanism of Diesel from Indirect Coal Liquefaction for Diesel Engine Combustion and Emission Simulations

New Reduced Kinetic Model for HCCI Engine Fuelled with Dimethyl Ether

Study of dimethyl ether homogeneous charge compression ignition combustion process using a multi-dimensional computational fluid dynamics model