Abstract:The plastic deformation mode and slip transfer between the alpha and beta phases of Ti-5Al-2.5Cr-0.5Fe-4.5Mo-1Sn-2Zr-3Zn titanium alloy were investigated using a combination of ex-situ scanning electron microscopy tensile tests and electron backscatter diffraction characterization. With increasing tensile strain, local orientation changes (which lead to the sub-grain boundary generation and migration) occurred in the alpha phase, resulting in grain subdivision/coalescence. Afterward, the elongated alpha grains were sub-divided (in general) into small equiaxed grains. Abrupt changes in the crystal orientation of the continuous beta-matrix were, however, rare. Three primary slip systems (prismatic and basal slip: alpha phase and {110}< 111 > slip: beta phase) accounted for more than 70% of the total slip system activity at each strain level. These systems could be activated with very low Schmid factors (<0.1) at high strains. The compatible deformation between the alpha and beta phases was realized mainly through the slip transfer correlated with the three primary slip systems, and the prismatic slip system was the most active system. In general, the alpha phase underwent plastic deformation first and compelled plastic deformation of the separated beta grains. Subsequently, the deformed beta grains transmitted the strain between an adjacent alpha grain and other alpha grains, leading to deviations from the uniaxial stress state in the local region. This resulted in wide distributions of the activated slip systems with various Schmid factors, and considerable strain concentration and failure in the alpha phase near the phase boundaries. (C) 2020 Elsevier B.V. All rights reserved.

Influence of stress-induced alpha" phase transformation on mechanical properties in metastable beta type Ti-5Al-2.5Cr-5Mo-1Sn alloy

Influence of stress-induced α’’ phase transformation on mechanical properties in metastable β type Ti-5Al-2.5Cr-5Mo-1Sn alloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Stress-induced Α″ Phase in a Beta Ti–19Nb–1.5Mo–4Zr–8Sn Alloy

Microstructural evolution, mechanical properties and fracture toughness of near β titanium alloy during different solution plus aging heat treatments

Strengthening Strain-Transformable Β Ti-alloy Via Multi-Phase Nanostructuration

Plastic deformation mode and / slip transfer of Ti-5Al-2.5Cr-0.5Fe-4.5Mo-1Sn-2Zr-3Zn titanium alloy at room temperature

Influence of cooling rate on phase precipitation and deformation mechanism of a novel metastable titanium alloy

Effect of Microscopic Stress and Strain on Mechanical Properties of Ti-6Al-2Zr-1Mo-1V Alloy

Deciphering the microstructural evolution and adiabatic shearing behavior of the titanium alloy with stress-induced ω phase transformation during dynamic compression

Effect of Thermo-Mechanical Treatment on Microstructure and Mechanical Property in Metastable beta Titanium Alloys

Unusual Stress-Induced Martensite Transformation in Ti-6Al-4V Alloy Enabled by Solution Treatment in the Lower Α+β Regime

Microstructural Evolution During Post-Heat Treatment and Its Effect on the Mechanical Properties of Directed Energy Deposited Near Β Titanium Alloy

Deformation-Induced Ambient Temperature Alpha-To-Beta Phase Transition And Nanocrystallization In (Alpha Plus Beta) Titanium Alloy

Revealing the decomposition mechanisms of dislocations and metastable phase and their effects on mechanical properties in a Ti-6Al-4V alloy

Dependency of Mechanical Properties in Ti-7Mo-3Al-3Cr-3Nb Alloy on the Β Phase Stability: Regulating Primary Α Phase

A Novel Sequential Mechanism Associated with Stress-Induced Β→ω→β+α Phase Transformation in Ti–6Mo-3.5Cr–1Zr Titanium Alloy

Composite Structure of Alpha Phase in Metastable Beta Ti Alloys Induced by Lattice Strain During Beta to Alpha Phase Transformation

In-situ Deformation Mechanisms of a Novel Ti-5Mo-4Cr-1V-1Zr Metastable Β Titanium Alloy

Metastable Phase Transformations and Mechanical Properties of an As-Extruded TiAl-based Alloy During Two-Step Heat Treatment

Effect of Primary Α Phase Fraction on Deformation Mechanism of Ti-1023 Alloy at Room Temperature