Abstract:Zirconium alloys have been used as primary materials for fuel cladding which protect the nuclear fuel from the outside in the nuclear power system. Zirconium alloys have very low absorption cross-section of thermal neutrons, high hardness, ductility, and corrosion resistance [1]. However, they had problems with nuclear reactor safety as they reacted violently with steam at high temperature, producing large amounts of hydrogen and heat, and having low mechanical strength at high temperature. Moreover, a massive hydrogen explosion by zirconium-steam interaction occurred at the Fukushima Daiichi nuclear power plant. The development of accident-tolerant fuel cladding has been widely studied since the Fukushima nuclear reactor accident [2]. Ideas and new concepts have been proposed for accident-tolerant fuel cladding to prevent hydrogen explosion by inhibiting reaction with steam in the accident environment. Therefore, the ATF research was actively carried out in the early development period to replace zirconium alloys using materials such as SiC, FeCrAl, etc., which have oxidation resistance better than zirconium [3,4]. However, the phenomenon of dissolution in cooling water under normal operating conditions was observed, and some materials had lower economic feasibility because the neutron absorption cross-section area was larger than zirconium. To overcome these problems, many researches are underway to take both stability and economy by coating the surface of zirconium cladding. By applying coating technology to zirconium cladding, it is easy to obtain corrosion resistance without a change in the base materials. Recently, Terrani et al. reported the oxidation resistance of Fe-based alloys for protecting zirconium alloys from the rapid oxidation in a high-temperature steam environment. Kim and co-workers also reported the corrosion behavior of Cr-coated zirconium alloy using a plasma spray and laser beam scanning [5]. In the present work, Cr anti-oxidation coating was fabricated on a commercial Zircaloy-4 cladding using cathodic arc ion plating (CAIP) because cathodic arc ion plated films tend be denser and have better adhesion characteristics than films produced using other method [6]. The Cr system was selected because of its good corrosion resistance. The microstructures of arc ion plated Cr coating were characterized. The oxidation behavior of the coating was analyzed. . 2. Experimental CAIP is well recognized method of producing protective coatings due to its high ionization efficiency and excellent film adhesion. It is a promising method for depositing oxidation-resistant coatings on nuclear fuel claddings. Pure Cr coating was deposited on the Zircaloy-4 using the CAIP with Cr target (99.59% purity). Figure. 1 shows the CAIP system which was designed to coat protective film onto the surface of a nuclear cladding. The substrates were cleaned ultrasonically in acetone and an ethanol solution, and the substrates were then mounted in a vacuum chamber. The chamber was evacuated to a pressure of 1 x 10 Torr, and heated simultaneously to 1473 K to remove the residual gas adsorbed on the chamber wall and substrates. Prior to the deposition, the substrates were sputter cleaned using Ar ions under -400V negative bias voltage for 5 min. Cr ion bombardment was applied to remove contaminants and ensure good adhesion of deposited coatings. The deposition of Cr was carried out in an Ar atmosphere with a pressure of 20mTorr. In order to study the effects of negative bias voltage, different negative bias voltages ranging from -25 to -100V were applied. After deposition, the coatings were polished to reduce the influence of the roughness, as well as for more precise measurements.

CHANGES IN ADHESION OF CrN COATINGS ON Zr-1%Nb ALLOY SUBSTRATES PRELIMINARY IRRADIATED WITH HIGH-INTENSE PULSED ION BEAMS

Corrosion Properties of Cr Coating Deposited on Nuclear Fuel Cladding

Preparation of Cr Hard Coatings by Ion Beam Assisted Electron Beam Vapor Deposition on Ni and Cu Substrates

Radiation-Induced Sharpening in Cr-Coated Zirconium Alloy

Effect of Preliminary Irradiation of 321 Steel Substrates with High-Intense Pulsed Ion Beams on Scratch Test Results of Subsequently Deposited AlN Coatings

Microstructural Understanding of CrN Layer As a Barrier Against Cr-Zr Interdiffusion in Cr-coated Zirconium Alloy for Accident Tolerant Fuel Claddings

Development and Characterization of CrN Films by Ion Beam Enhanced Deposition for Improved Wear Resistance

The high-temperature oxidation and mechanical properties of the Cr/Zr and CrN/Zr coating

Deposition, microstructure and nanoindentation of multilayer Zr nitride and carbonitride nanostructured coatings

Early-stage Diffusion and Oxidation Behavior of Cr-Nb Coated Zr Alloy Accident Tolerant Fuel Cladding Materials at 1200°C - 1500°C

Effect of Ion Bombarding Energy on the Properties of ZrN/TiAlN Nanometer Multilayered Coatings

Improvement Properties of Protective Coatings on Zirconium Alloys and Austenitic Stainless Steels by Pre-Treatment with High-Intense Pulsed Ion Beams

Cr-coated Zr-4 alloy prepared by electroplating and its in situ He+ irradiation behavior

In-situ analysis of ZrN/CrN multilayer coatings under heating

Tribological Behaviors in Air and Seawater of CrN/TiN Superlattice Coatings Irradiated by High-Intensity Pulsed Ion Beam

Study on the Structure and Tribological Properties of Crn Coating by Ibed

Changing Mechanisms of High-Temperature Oxidation of Zr-1%Nb Alloy in Air and Steam by Surface Modification with Charged Particles

Effects of ion irradiation on chromium coatings of various thicknesses on a zirconium alloy

Chromium Coatings Applied to Zr Alloy Claddings by Cathodic Arc Ion Plating: Effect of Nitrogen Inclusion on Limiting Columnar Defects

Influence of Zr on Structure, Mechanical and Thermal Properties of Cr–Al–N Coatings

Effects of Nitrogen Content on the Phase Composition and High-Temperature Steam Oxidation Resistance of Cr0.5Al0.5Nx (x = 0.33, 0.81, 1.23) Coatings on Zry-4 Alloy