Abstract:Aluminum alloys, characterized by their low density and high mechanical strength, are widely applied in the manufacturing sector. However, the application of aluminum alloys in extreme environments presents severe corrosion challenges. Sol–gel organic coating techniques have garnered significant attention due to their excellent stability, barrier properties, and cost-effectiveness, as well as their simpler processing. Nevertheless, conventional sol–gel coatings are unable to withstand the corrosive effects of high-chloride and high-halide ion environments such as marine conditions, owing to their inherent structural defects. Therefore, this study proposes the utilization of a simple method to synthesize catechol (CA) and meta-phenylenediamine (MPD)-derived catecholamine compounds to modify sol–gel coatings. Surface characteristics of the modified coatings were analyzed using Fourier-transform infrared spectroscopy (FT-IR), ultraviolet-visible (UV-Vis) spectroscopy, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The thickness of the modified coating was approximately 6.8 μm. The CA/MPD-modified substance effectively densifies the sol–gel coating, enhancing its corrosion protection performance. A 3.5 wt% NaCl solution was used to simulate a marine environment, and electrochemical impedance spectroscopy (EIS) was conducted using an electrochemical workstation to evaluate the coating's protective properties over a long-term period. The results indicate that the modified coating provides protection for 3003 aluminum alloy for a minimum of 30 days under corrosive conditions, outperforming unmodified sol–gel coatings in terms of corrosion resistance.

The Golden Alloy Cu5Zn5Al1Sn: Effect of Immersion Time and Anti-Corrosion Activity of Cysteine in 3.5 Wt% NaCl Solution

Effect of Aging Time on the Corrosion Behavior of a Cu-Ni-Si Alloy in 3.5 wt% NaCl Solution

Corrosion behavior and electrochemical properties of carbon steel, commercial pure titanium, copper and copper–aluminum–nickel alloy in 3.5% sodium chloride containing sulfide ions

Understanding Corrosion Mechanism of Sn–Zn Alloys in NaCl Solution Via Corrosion Products Characterization

Effects of Al addition on corrosion behavior and mechanical property of high-strength and high-elasticity Cu-20Ni-20Mn-0.3Nb-0.3Cr-0.3Zr alloy

Changes of Corrosion Electrochemical Behavior of Cerium Nitrate Doped GPTMS/TEOS Silane Hybrid Films with Immersion Time

Electrochemical Behavior of Zn-xSn High-Temperature Solder Alloys in 0.5 M NaCl Solution

Effect of CaCl2 and NaHCO3 in Physiological Saline Solution on the Corrosion Behavior of an As-Extruded Mg–Zn–Y–Nd alloy

Effect of Al Content on the Long-Term Corrosion Behavior of Arc-Sprayed ZnAl Alloy Coatings

Corrosion Behavior of Al Modified with Zn in Chloride Solution

Effects of Cu-content and passivation treatment on the corrosion resistance of Al0.3CuxCoCrFeNi high-entropy alloys

Characterization of the Anodic Film and Corrosion Resistance of an A535 Aluminum Alloy after Intermetallics Removal by Different Etching Time

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution

Effect of Solid-Solution Treatment on Corrosion and Electrochemical Behaviors of Mg-15Y Alloy in 3.5 Wt.% NaCl Solution

Corrosion behavior of FeCoNiCrCux high-entropy alloys in 3.5% sodium chloride solution

Catechol/m-Phenylenediamine Modified Sol–Gel Coating with Enhanced Long-Lasting Anticorrosion Performance on 3003 Al Alloy

Corrosion Inhibition Efficiency of Cysteine-Metal ions Blends on Low Carbon Steel in Chloride-Containing Acidic Media

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings

The initial corrosion mechanism of hot-dipping Zn–Al–Mg alloy coating in chloride-containing solution

Effect of Al Addition on Electrochemical Behavior of Sn-0.7Cu-xAl Lead-Free Solders Alloys in 3.5 wt.% NaCl Solution

Effect of Copper(II) Ions on Corrosion Resistance of Al-Zn Coated 5052 Aluminum Alloy in Seawater