Abstract:Plasma facing components (PFCs) in the next generation of tokamak devices will operate in challenging environments, with heat loads predicted to exceed 10 MWm$^{-2}$. The magnitude of these heat loads is set by the width of the channel, the "scrape-off layer" (SOL), into which heat is exhausted, and can be characterised by an e-folding length scale for the decay of heat flux across the channel. It is expected this channel will narrow as tokamaks move towards reactor relevant conditions. Understanding the processes involved in setting the SOL heat flux width is imperative to be able to predict the heat loads PFCs must handle in future devices. Measurements of the SOL width are performed on the high-field spherical tokamak, ST40, using a newly commissioned infrared thermography system. With its high on-axis toroidal magnetic field ($\geq$1.5 T) ST40 is uniquely positioned to investigate the influence of toroidal field on the heat flux width in spherical tokamaks, whilst also extending measurements of the SOL width in spherical tokamaks to increased poloidal field ($\geq$0.3 T). Due to the divertor on ST40 having a low degree of axisymmetry, it is necessary for a set of radial measurements of the heat flux to be taken across the divertor, made possible using an automated toolchain that fully incorporates its 3D geometry. These radial profiles are combined with the magnetic topology of the plasma to infer the width of the SOL, with both single and double exponential profiles of heat flux observed. A reduction in the heat flux is observed toroidally across part of the divertor, with preliminary investigations indicating that partial shadowing occurs, resulting from the separation between magnetic field lines and trailing edges upstream of the observed region becoming comparable to the ion gyro-radius.

A Method to Identify the Heat Flux from Photons and Neutrals at the Divertor Target

Development of Surface Eroding Thermocouples in Small Angle Slot Divertor in DIII-D

Experimental Observation of Heat Flux Mitigation During Divertor Detachment in the DIII-D Small Angle Slot Divertor

Diagnostic options for radiative divertor feedback control on NSTX-U

Analysis of Divertor Heat Flux with Infrared Thermography During Gas Fuelling in the Hl-2a Tokamak

Calculation of in-situ steady-state heat flux on EAST lower divertor

Study of Heat Load on EAST Divertor Plates by an Infrared Camera

Upgrade of an Integrated Langmuir Probe System on the Closed Divertor Target Plates in the HL-2A Tokamak

Inferring the scrape-off layer heat flux width in a divertor with a low degree of axisymmetry

Reconstruction of Heat Flux Profile on the Hl-2a Divertor Plate with A Three-Dimensional Analysis Model

Study on Divertor Plasma Behavior Through Sweeping Strike Point in New Lower Divertor on EAST

Ion Temperature Measurements in the MAST-U Divertor During Steady State Plasmas and ELM Burn Through Phenomena

Thermo-hydraulic performance of tungsten flat tile type divertor target with two types of novel engineered cooling channel wall

Reversed-direction 2-point modelling applied to divertor conditions in DIII-D

Study of Divertor Heat Flux Widths in Type-I Elmy H-Mode with Infra-Red Thermography on East Tokamak

Comparison of Measurements with Different Types of Divertor Langmuir Probe in EAST Tokamak

Novel data interpretation method for DIII-D divertor retarding field energy analyzer with 3-D particle-in-cell simulations

Estimation of Peak Heat Flux Onto the Targets for CFETR with Extended Divertor Leg

E × B Flow Driven Electron Temperature Bifurcation in a Closed Slot Divertor with Ion B × ∇B Away from the X-point in the DIII-D Tokamak

Exploration of Non-Resonant Divertor Features on the Compact Toroidal Hybrid

Investigation of pedestal parameters and divertor heat fluxes in small ELM regimes on DIII-D