Abstract:Characteristic widths of divertor power load footprints, i.e., power decay length lambda(q), Gaussian dissipation width S and integral power width lambda(int) in radio-frequency (RF) heated type-I ELMy H-modes are investigated with infra-red (IR) thermography diagnostic on experimental advanced superconducting tokamak (EAST). The fitting of divertor heat flux profile to Eich function is employed to obtain lambda(q) and S [2]. The heat flux widths on lower-outer (LO) divertor plates are found larger than those of lower-inner (LI) plates, and obvious multi-peak structures are found on LO divertor power load footprints. A comparison of LI heat flux widths of ELM-averaged in type-I ELMy H-mode to those within inter-ELM phases indicates that the widths are similar, in magnitude, for the two cases. The lambda(q) mapping to the outer mid-plane (OMP) from the LI divertor has a strong inverse dependence on I-p (or equivalently poloidal magnetic field at the OMP, B-p,B-omp) in the form of lambda(EAST,type-I)(q) = (2.45 +/- 0.3) x I-p(-1.01 +/- 0.11) (or lambda(EAST,type-I)(q) = (0.64 +/- 0.17) x B-p,omp(-1.02 +/- 0.14)), which is in satisfactory agreement, in tendency, with the multi-machine experimental scaling results and heuristic drift-based model proposed by Goldston. In addition, the linear regression of ELM-averaged S, on LI divertor during type-I ELMy H-mode, with I-p shows a decrease tendency, being consistent with the case of LO target in EAST type-III ELMy H-mode. This work may provide useful information for the extrapolation to ITER, whose baseline operation scenario is type-I ELMy H-mode. (c) 2016 Elsevier B.V. All rights reserved.

Reconstruction of Heat Flux Profile on the Hl-2a Divertor Plate with A Three-Dimensional Analysis Model

OV / 4-5 1 Overview of Experimental Results on the HL-2 A Tokamak

Analysis of Divertor Heat Flux with Infrared Thermography During Gas Fuelling in the Hl-2a Tokamak

Divertor Heat Flux Mitigation Using Supersonic Molecular Beam Injection in Type-Iii Elmy H Mode Plasmas of Hl-2a Tokamak

Divertor footprint modeling due to RMP in HL-2A and role of plasma response

Analyses of Monoblocks Divertor at One-Sided High Heat Flux Using RPI Wall Boiling Model

Thermomechanical Measurements for a Flat-Type Divertor Mock-Up: A Benchmark for Simulation

Numerical Simulation in A Subcooled Water Flow Boiling for One-Sided High Heat Flux in Reactor Divertor

Study of Divertor Heat Flux Widths in Type-I Elmy H-Mode with Infra-Red Thermography on East Tokamak

Reversed-direction 2-point modelling applied to divertor conditions in DIII-D

Assessment of the W7-X High Heat Flux Divertor with Thermo-Mechanical Analysis

Upgrade of an Integrated Langmuir Probe System on the Closed Divertor Target Plates in the HL-2A Tokamak

Divertor modelling for conceptual studies of tokamak fusion reactor FDS-III

Study of Heat Load on EAST Divertor Plates by an Infrared Camera

Mhd Equilibrium Configuration Reconstructions for Hl-2a Tokamak

Thermo-hydraulic performance of tungsten flat tile type divertor target with two types of novel engineered cooling channel wall

Calculation of in-situ steady-state heat flux on EAST lower divertor

Experimental Observation of Heat Flux Mitigation During Divertor Detachment in the DIII-D Small Angle Slot Divertor

The mechanism research of double strike points of the divertor particle flux in hl-2a ecrh plasmas

Three-dimensional modeling and thermal hydraulic analysis of high temperature gas-cooled reactor core

Study of W/Cu Flat-Type Mock-Ups with Novel Hypervapotron Cooling Structure for CFETR Divertor