Abstract:Ni-based wrought superalloys are widely used in the hot section of aircraft gas turbine engines for their capability in retaining strength and resisting creep, fatigue, and oxidation at elevated temperature. With the development of the newer generation turbine disk alloys, it is highly imperative for aircraft engine manufacturers to substantiate the use of the materials by conducting a thorough examination of their mechanical properties. As these components are subjected to elevated temperatures and complex stress state in the service process where time dependent creep is the primary deformation failure mechanism and life-limiting factor for the component, it is of great importance to evaluate the relationship between microstructure, creep behavior and the underlying creep deformation mechanism. Therefore, the main objective of the present research aims at investigating the fundamental relationship between external creep condition and internal creep deformation mechanism in a new wrought superalloy with low stacking fault energy (SFE). In order to study the influences of the loading stress level and temperature on the creep deformation mechanism, stress range of 345-840 MPa and temperature range of 650-815 degrees C were selected to carry out the creep experiment. The results show that two kinds of gamma' with different diameters distributed in the matrix and the larger one began to coarsen when the creep temperature increased to 725 degrees C. Under creep temperature of 650 degrees C, the formation of SF resulted from the shearing of gamma' by dislocations dominated the creep deformation. When the temperature range was raised up to 725-760 degrees C, SF and microtwins were the main microstructures after creep deformation. With further increasing the temperature and load, instead of accommodating only in the gamma', the SF and microtwins penetrated the whole gamma' and matrix area. When the temperature was increased to 815 degrees C, the climb/bypass mechanism controlled the creep process.

Creep Anisotropy Behavior, Deformation Mechanism, and Its Efficient Suppression Method in Inconel 625 Superalloy

Inconsistent creep between dendrite core and interdendritic region under different degrees of elemental inhomogeneity in nickel-based single crystal superalloys

In Situ SEM Study of Creep Deformation Behavior of Nickel-Based Single-Crystal Superalloys

Creep Behavior and Deformation Mechanism of a Third-Generation Single Crystal Ni-Based Superalloy at 980 °C

Creep‐fatigue Deformation Characteristics and Life Prediction Model of Inconel 718 Superalloy under Hybrid Stress–strain‐controlled Mode

Effect of pre-straining treatment on high temperature creep behavior of Ni-based single crystal superalloys

Experimental Investigation and Numerical Prediction on Creep Crack Growth Behavior of the Solution Treated Inconel 625 Superalloy

Small punch creep test reveals the differences of high-temperature creep behaviours for laser powder bed fusion and Rolled Inconel 718 alloys

The creep deformation of a new nickel-base alloy-by-design studied using synchrotron X-ray diffraction

Creep Behavior and a Deformation Mechanism Based Creep Rate Model under High Temperature and Low Stress Condition for Single Crystal Superalloy DD5

Anisotropy in creep-aging behavior of Al–Li alloy under different stress levels: experimental and constitutive modeling

Experimental characterization of flat indentation creep behaviour of Inconel 617

Serrated flow behavior and microstructure evolution of Inconel 625 superalloy during plane-strain compression with different strain rates

Effect of Creep Process on the Microstructural Evolution and Deformation Behavior of a New Powder Metallurgy Ni-Based Superalloy

Studies of High-Temperature Fatigue Behavior and Mechanism for Nickel-Based Superalloy Inconel 625

Mechanisms of deformation, damage and life behavior of inconel 617 alloy during creep-fatigue interaction at 700 °C

Study of the Creep Behavior of Nickel-Based Single Crystal Superalloy Micro Specimens with Dimensional Effects

Creep Mechanism of A Ni-Co Base Wrought Superalloy

Creep Anisotropy Characteristics and Microstructural Crystallography of Marine Engineering Titanium Alloy Ti6321 Plate at Room Temperature

Study of precipitation-assisted stress relaxation and creep behavior during the ageing of a nickel-iron superalloy

Creep behaviors and deformation mechanisms at intermediate temperatures in a novel γ‐γ' nickel‐based superalloy