Abstract:Abstract Combined measurements of shear stress relaxation and differential dynamic storage and loss shear moduli G′ and G′′ have been made on styrene-butadiene rubber (type 1502) containing 50 phr N299 carbon black and 10 phr Sundex 790 oil, both cured and uncured, and compared with similar measurements on the cured and uncured gum rubber. The range of temperature was −22.5° to 63°C, and of static shear strain 0.01 to 0.40; the maximum oscillatory shear strain was about 0.005 and the frequency was usually 0.64 Hz. Dynamic measurements of G′ and G′′ with no superposed static strain and stress relaxation measurements at small strains on the filled samples could be reduced by frequency-temperature superposition with αT shift factors that were somewhat larger than those that applied to the raw or crosslinked gum. At about 0.6 Hz, the filler increased the storage modulus by about a factor of 5 for the cured sample and about 10 for the uncured; the moduli for the cured and uncured filled samples were almost identical. The order of rates of relaxation was unfilled uncured > filled uncured > filled cured > unfilled cured. At small static strains, the stress relaxation of the filled samples (both uncured and cured) was substantial, but the differential dynamic moduli G′ and G′′ remained nearly equal to their values with zero static strain throughout the relaxation process. With increasing static strain γ, the strain-dependent relaxation modulus G(γ;t) decreased by as much as a factor of 3 for the filled, cured sample and 4 for the filled, uncured sample. The modulus G(γ;t) could not be factored into a strain-dependent and a time-dependent function. During stress relaxation of the filled samples (both cured and uncured) at large strains, the differential storage modulus G′(ω,γ;t) experienced a drop followed by slow recovery toward its initial value at 25°C; the loss modulus G′′(ω,γ;t) was unchanged. For the filled, cured sample, complete recovery to the initial value G′(ω,0) (where 0 refers to zero static strain) was accomplished by removing the shearing stress and heating for one day at 63° followed by return of the temperature to 25°C. The results are interpreted in terms of a structure which combines a crosslinked (or, in the case of uncured, an entangled) polymer network and a network of carbon black particles. At small strains, stress relaxation is thought to be accomplished primarily by rearrangements of carbon particles and/or polymer molecules bridging them, without structural damage in the sense that the rearranged structure has the same properties as the original. These rearrangements are impeded by crosslinking in the cured vis-a-vis the uncured filled rubber. The kinetics of rearrangement may be governed by configurational changes of the polymer molecules since the temperature shift factors do not differ greatly from those for the gum rubber. At large strains, the particle network can be damaged but can regain its structure by a healing process which is accelerated at higher temperatures. The conclusions apply to the particular compound studied here and not necessarily to other rubber-black compounds, which according to the literature show great diversity of properties.

Effect of Cyclic Straining with Various Rates on Stress Softening/hysteresis and Structural Evolution of Filled Rubber: A Time-Resolved SANS Study

Shear Behaviour of Sand-Rubber Mixtures: Interpretation from Energy Transformation and Force Chain Evolution

Experimental Characterization and Finite Element Modeling the Deformation Behavior of Rubbers with Geometry Defects

Effect of Strain Rate on Tension Response of Filled Silicone Rubber

Tension Testing of Silicone Rubber at High Strain Rates

Linear Rheology of Natural Rubber Compounds Filled with Silica, Short Nylon Fiber or Both

Permanent Deformation Characteristics of Saturated Sand under Cyclic Loading

A Network Evolution Model for Recovery of the Mullins Effect in Filled Rubbers

Nonlinear Stress Relaxation of Silica Filled Solution‐polymerized Styrene–butadiene Rubber Compounds

Microstructure Evolution and Strain Softening of Carbon Black Filled Natural Rubber Vulcanizates

Structural Origin for the Strain Rate Dependence of Mechanical Response of Fluoroelastomer F2314

Large amplitude oscillatory rheology of silica and cellulose nanocrystals filled natural rubber compounds

Structural evolution during uniaxial deformation of natural rubber reinforced with nano-alumina

Experimental Investigation and Constitutive Modeling of Uncured Carbon Black Filled Rubber at Different Strain Rates

Effects of Various Filler Surfaces on Tuning the Hierarchical Structures and Reinforcement of Silicone Rubbers

Payne effect and Mullins effect of silica filled butadiene rubber nanocomposites vulcanizates and their unextractable gels

Linear and nonlinear rheological behaviors of silica filled nitrile butadiene rubber

Cavity Formation in Silica-Filled Rubber Compounds Observed During Deformation by Ultra Small-Angle X-Ray Scattering

Nonlinear Rheological Behavior of Silica Filled Solution‐polymerized Styrene Butadiene Rubber

Tailoring Reinforcement and Strain Softening Behaviors of Natural Rubber Vulcanizates Nanocomposites by Dopamine-Modified Silica

Stress Relaxation and Differential Dynamic Modulus of Carbon Black-Filled Styrene-Butadiene Rubber in Large Shearing Deformations