Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Determination of the Through-Thickness Residual Stress in Thick Duplex Stainless Steel Welded Plate by Wavelength-Dependent Neutron Diffraction Method

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

A Study of Residual Stress in the Repair Weld of Stainless Steel Clad Plate by Neutron Diffraction Measurement and Finite Element Method

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

Neutron Diffraction Measurement and Numerical Simulation to Study the Effect of Repair Depth on Residual Stress in 316L Stainless Steel Repair Weld

Numerical Analysis of Welding Residual Stress and Its Verification Using Neutron Diffraction Measurement

Weld Residual Stresses in A Thick Plate Considering Back Chipping: Neutron Diffraction, Contour Method and Finite Element Simulation Study

Electromagnetic Ultrasonic Measurement for Welding Residual Stress Detection - Comparison Between Experiment with Numerical Simulation

Neutron and X-ray Diffraction Analysis of Macro and Phase-Specific Micro Residual Stresses in Deep Rolled Duplex Stainless Steels

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Experimental Research of Welding Residual Stress of Butt Welded Joint of Thick Steel Plate

Nonhomogeneous Microstructure Formation and Its Role on Tensile and Fatigue Performance of Duplex Stainless Steel 2205 Multi-Pass Weld Joints

Neutron diffraction methods for the study of residual stress fields

Comparison of residual stress determination using different crystal planes by short-wavelength X-ray diffraction in a friction-stir-welded aluminum alloy plate

Experimental Characterisation and Numerical Modelling of Residual Stresses in a Nuclear Safe-End Dissimilar Metal Weld Joint

Study of Residual Stress Variation with Depth of Friction Stir Welded Aluminium Plates with Different Thicknesses

Recent Progress Of Residual Stress Distribution And Structural Evolution In Materials And Components By Neutron Diffraction Measurement At Rsnd

Fatigue Failure Mechanism of Duplex Stainless Steel Welded Joints Including Role of Heterogeneous Cyclic Hardening/softening: Experimental and Modeling

Stress and distortion of the 10 mm thick plate EH40 and 316L different butt joints in 10 kW laser welding

Numerical and experimental study of residual stress in multi-pass laser welded 5A06 alloy ultra-thick plate