Abstract:The process of in-situ oil shale extraction via convection heating is accompanied by complex solid–fluid-thermal-mass transfer multi-field coupling effects. As the fluid temperature increases, thermal cracking and pyrolysis occur within the oil shale, forming a highly permeable and porous structure, resulting in the oil shale being subjected to complex stress field changes. This paper, set against the background of the in-situ oil shale extraction process using steam injection, conducts uniaxial compression tests on oil shale under different bedding directions under the real-time action of high-temperature steam. Combined with micro-CT, XRD and XPS analysis of oil shale, the characteristics of anisotropic evolution of compressive strength of oil shale under the real-time action of high-temperature steam and the internal mechanisms occurring are clarified. As the steam temperature increases, the compressive strength and elastic modulus of oil shale in different bedding directions show a trend of decreasing and then increasing, reaching their lowest values at a steam temperature of 400 °C. The rate of change in compressive strength of oil shale perpendicular and parallel to the bedding direction differs significantly at different pyrolysis stages. When the steam temperature exceeds 400 °C, the rate of increase in compressive strength of oil shale in the vertical bedding direction is significantly higher than in the parallel bedding direction. At high temperatures, the fracturing of oil shale is primarily along the bedding planes, while the development of interlayer fractures is relatively slow, resulting in higher strength of oil shale in the vertical bedding direction. The failure characteristics of oil shale perpendicular to the bedding direction transition from brittle shear fracturing to semi-brittle shear fracturing and then to plastic deformation, eventually returning to semi-brittle shear fracturing. In contrast, the failure characteristics of oil shale parallel to the bedding direction transition from brittle shear fracturing through semi-brittle shear fracturing to plastic deformation. During pyrolysis process, the content of clay minerals inside the oil shale does not change significantly, but the change in non-clay minerals is most pronounced. When the temperature exceeds 400 °C, the diffraction-peak intensity of pyrite suddenly decreases or even disappears, the diffraction-peak intensity of kaolinite gradually decreases, and the content changes of elements such as C, O, Al, Si are also more noticeable. The transformation of internal mineral composition in oil shale (e.g., the conversion of kaolinite to metakaolinite) is the fundamental reason for the strength increase of oil shale at temperatures above 400 °C.

Changes in Thermophysical and Thermomechanical Properties of Thermally Treated Anisotropic Shale after Water Cooling

Stress Wave Interaction with a Nonlinear and Slippery Rock Joint

Insight into Spontaneous Water-Based Working Fluid Imbibition on the Dynamic Tensile Behavior of Anisotropic Shale

Mechanical Response to Dynamic Compressive Load Applied to Shale after Thermal Treatment

Experimental Investigation on the Effects of Thermal Treatment on the Physical and Mechanical Properties of Shale

Effect of Heating–cooling Cycles on Mechanical Properties and Microscopic Characteristics of Shale

Experimental Investigation of the Tensile Behavior and Acoustic Emission Characteristics of Anisotropic Shale under Geothermal Environment

Experimental and numerical investigation on the fracture behavior of deep anisotropic shale reservoir under in-situ temperature

Experimental Investigation on the Sudden Cooling Effect of Oil-Based Drilling Fluid on the Dynamic Compressive Behavior of Deep Shale Reservoirs

Study on the Change of Physical Properties of Organic-rich Shale after Heat Treatment

Effect of Water-Based Working Fluid Imbibition on Static and Dynamic Compressive Properties of Anisotropic Shale

Experimental and constitutive modeling of the anisotropic mechanical properties of shale subjected to thermal treatment

Thermal Effects on Mechanical and Failure Behaviors of Anisotropic Shale Subjected to Direct Shear

Investigation of Formation Heat Treatment to Enhance the Multiscale Gas Transport Ability of Shale

Research on the Mechanical Properties and Anisotropy Evolution of Uniaxial Compression of Oil Shale Under Real-Time High-Temperature Steam

Experimental Study on Mechanical, Brittleness, and Fracture Behavior of Deep Shales Subjected to Fracturing Fluid-Shale Interactions at Reservoir Temperature and In-Situ Stress Conditions

Experimental Investigation of Anisotropic Thermal Deformation of Oil Shale Under High Temperature and Triaxial Stress Based on Mineral and Micro-fracture Characteristics

Heating-Induced Enhancement of Shale Gas Transport and Its Application for Improving Hydraulic Fracturing Performance

Thermal Behavior of Minerals in Shale and Its Influence on Evolution of Gas-Flow Channels under Thermal Shock

Determination of Mechanical Property Evolutions of Shales by Nanoindentation and High-Pressure CO2 and Water Treatments: A Nano-to-Micron Scale Experimental Study

An Experimental Investigation of the Thermophysical Properties of Shale Reservoirs: A Case Study of the Wufeng-Longmaxi Formation in the Jiaoshiba Area