Abstract:High molecular weight polyether polyols are widely used. However, there is not only a large risk of reaction heat, but also a long reaction time in its traditional production process by using the semi-continuous reactor. The microchannel reactor（MCR） has the characteristics of high heat transfer efficiency and process safety,but the viscous material and high reaction heat release make it difficult to produce the high molecular weight polyether polyols. In this work, using double metal complex（DMC） as catalyst and n-hexane as solvent, the ringopening polymerization of propylene oxide（PO） was carried out in MCR. Polypropylene glycol（PPG） with molecular weight ranging from 2000 to 8000 was prepared. Effects of reaction conditions, such as flow rate, channel length,reaction temperature and feed policy, were investigated. It has been found that when the residence time is long enough, the molecular weight of the produced PPG is basically equal to the theoretical molecular weight. When the flow rate of initiator is fixed, an increase in flow rate of monomer will result in the molecular weight distribution（MWD） first widened and then narrowed. If the tube length is longer, the molecular weight is larger and the MWD is wider. If the temperature increases, the induction period of the polymerization can be shortened. Using the segmented feed, it is easier to prepare high molecular weight PPG with higher conversion than using the single feed, but the MWD is wider. These rules can be explained from the mechanism of PO ring-opening polymerization catalyzed by DMC and micro-mixing strength of materials in MCR. The lower the micro-mixing strength, and the smaller the rate ratio of chain transfer to chain propagation in polymerization, the wider the molecular weight distribution is.

Highly Efficient Two‐stage Ring‐opening of Epichlorohydrin with Carboxylic Acid in a Microreaction System

Record Productivity And Unprecedented Molecular Weight For Ring-Opening Copolymerization Of Epoxides And Cyclic Anhydrides Enabled By Organoboron Catalysts

High‐Activity Organocatalysts for Polyether Synthesis Via Intramolecular Ammonium Cation Assisted SN2 Ring‐Opening Polymerization

Ring-Opening Polymerization of Propylene Oxide by Double Metal Complex in Micro-Reactor

Preparation of high molecular weight polypropylene glycol in microchannel reactor

Preparation of 2, 3-Epoxypropyl Neodecanoate: Process Optimization and Mechanism Discussion

Process Intensification of Heterogeneous Dehydrochlorination of Β-Chlorohydrins by Using N-Propanol As Co-Extractant

Dehydrochlorination of -chlorohydrin in continuous microflow system: Reaction kinetics and process intensification

Diphenyl Phosphate/ethyl Diphenylphosphinite As an Efficient Organocatalytic System for Ring-Opening Polymerization of Ε-Caprolactone and Δ-Valerolactone

Ring Opening Copolymerization of Epoxides with CO2 and Organic Anhydrides Promoted by Dinuclear [OSSO]‐type Metal Complexes

Simultaneous Dynamic Kinetic Resolution in Combination with Enzymatic Ring-Opening Polymerization

Two‐Phase Reactions in Microdroplets Without the Use of Phase‐Transfer Catalysts

Evaluation of an Improved Epichlorohydrin Synthesis from Dichloropropanol Using a Microchemical System

Tetramethylammonium Neodecanoate As a Recyclable Catalyst for Acidolysis Reaction of Epichlorohydrin with Neodecanoic Acid

Rare Garth Polymer Complex Catalyst For Ring-Opening Polymerization Of Epichlorohydrin

Epoxidation of Fatty Acid Methyle Ester with hydrodynamic cavitation technology

Direct Esterification in Helical Continuous-Flow Microreactors under an Aqueous Environment: Optimization, Reaction Kinetics, and Process Intensification

Synthesis of Epichlorohydrin from 1,3-Dichloropropanol Using Solid Base

Regio-selective synthesis of polyepichlorohydrin diol using Zn–Co(III) double metal cyanide complex

Advancing H-Bonding Organocatalysis for Ring-Opening Polymerization: Intramolecular Activation of Initiator/Chain End

Controlled Ring-Opening Polymerization of Macrocyclic Monomers Based on Ring-Opening/Ring-Closing Cascade Reaction