Abstract:<p>Studies on the rheoforming of high melting point alloys are scarce due to the difficulties in preparing semisolid slurries. This work applied a novel enclosed cooling slope channel (ECSC) to prepare a semisolid slurry and squeeze cast a CuSn10P1 (weight percent) alloy. The microstructure and phase formation of the semisolid slurry, properties of liquid squeeze casting, rheo-squeeze casting with or without isothermal treatment of the semisolid slurry were investigated through X-ray diffraction, scanning electron microscopy, electron probe microanalysis, nanoindentation, and transmission electron microscopy. The results show that the microstructure is transformed from coarse dendrites of as-cast to equiaxed grains of semisolid. The high cooling rate of the ECSC process and the semisolid slurry isothermal treatment suppressed tin diffusion to induce the formation of the metastable phase β′-Cu<sub>13.7</sub>Sn. The average values of the modulus and micro-hardness of the rheo-squeeze part after soaking for 20 s were 121.99 ± 14.03 GPa and 2.01 ± 0.94 GPa, which was lower than that without isothermal and liquid squeeze casting, indicating that it has good deformability. The tensile strength and elongation of the rheo-squeeze part after 20 s of soaking treatment are 417 MPa and 12.6%, which increase by 26.3% and three times, respectively, compared to those without isothermal and liquid squeezing, which is likely attributed to solution strengthening, fine grain strengthening, and microstructure homogenization. In addition, the fracture mechanism was transformed from the brittle fracture of liquid squeeze and rheo-squeeze casting without isothermal treatment to a combination of cleavage fracture and ductile fracture of rheo-squeeze casting with 20 s of soaking treatment.</p>

A distinctive Pb-Sn semi-solid additive manufacturing using wire feeding and extrusion

Synthesis of Fine Pb–50 Vol.-%Sn Alloys by a New Process of Reciprocating Extrusion

A Novel Ultrasonic Rolling Assisted Direct Energy Deposition Method with Semi-Solid Thixo-Forming Characteristics for Aa6061

Controllable fabrication of Sn–Bi alloy microspheres for improved lead-free solder

Additive Manufacturing of Sn63pb37 Component by Micro-Coating

Wire-based friction stir additive manufacturing towards isotropic high-strength-ductility Al-Mg alloys

Microstructure and tensile properties of Sn-1Cu lead-free solder alloy produced by directional solidification

Study on Semisolid Rheo-Diecasting Process, Microstructure and Mechanical Properties of Mg-6Al-1Ca-0.5Sb Alloy with High Solid Fraction

Numerical Simulation and Experimental Research on Fused-Coating Additive Manufacturing of Sn63Pb37 Thin-Walled Structures

An investigation into Ti-22Al-25Nb in-situ fabricated by electron beam freeform fabrication with an innovative twin-wire parallel feeding method

Micromechanisms of Medical Mg-Zn alloys during Semi-solid powder forming (SPF)

Developments of high strength Bi-containing Sn0.7Cu lead-free solder alloys prepared by directional solidification

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

Laser additive manufacturing of Zn metal parts for biodegradable applications: Processing, formation quality and mechanical properties

The Grain Refinements Effect of Zn Alloying on Low-Temperature Sn–Bi–In Lead-Free Solder

A high-performance Mg-Al-Sn-Zn-Bi alloy fabricated by combining sub-rapid solidification and hot rolling

Radial bimetallic structures via wire arc directed energy deposition-based additive manufacturing

Development of a Fused Deposition Modeling System for Low Melting Temperature Metal Alloys

Effect of twin-wire feeding methods on the in-situ synthesis of electron beam fabricated Ti-Al-Nb intermetallics

A study of selective laser melting process for pure zinc and Zn10mg alloy on process parameters and mechanical properties

Microstructure and Mechanical Properties of Sn–Bi Solder Joints Reinforced with Zn@Sn Core–shell Particles