Abstract:Phase change materials are thermal energy storage materials with high heat storage density, low temperature loss and long cycle life. However, they also show a weak light absorption ability and low thermal conductivity, limiting their applicability for solar thermal conversion and storage technologies. In this paper, in order to improve the relatively low thermal conductivity of stearic acid and enhance its thermal conductivity, SGC-T composites with enhanced thermal conductivity were prepared using metallurgical slag, via the melt blending method. The SEM and EDS, surface scanning tests, were used to determine the morphology characteristics of the composite phase change materials and verify the addition of metallurgical slag. The physical phase composition, structure, and absorption coefficients were analyzed by XRD, FT-IR, and UV-Vis-NIR analyses. The thermophysical properties were analyzed by DSC. The thermal stability was explored using TG testing. The thermal conductivity was explored by measuring the thermal conductivity coefficient value of the samples at the testing temperature of 25 celcius using the hot disk method/transient flat plate heat source method. The heat storage and exothermic capabilities of the samples were evaluated by the photo-thermal warming system/infrared thermography test. The results showed that the thermal conductivity of SGC was 0.663 W center dot(m center dot K)- 1, and that of SGC-2 T, SGC-6 T, SGC-10 T, SGC-14 T, were 0.695 W center dot(m center dot K)- 1, 0.758 W center dot(m center dot K)- 1, 0.824 W center dot(m center dot K)- 1 and 0.872 W center dot (m center dot K)- 1, respectively, which are comparable to SGC. Compared with SGC, the thermal conductivity values of the four composite phase change materials increased by 4.8%, 14.3%, 24.3%, and 31.5%, respectively. SGC-14 T has the best heat transfer performance, which significantly improves the heat transfer performance during latent heat storage and release. Therefore, the SGC-14 T material reported in this work is a promising candidate in the field of energy-saving conversion, and further expands the applicability of phase change materials.

Paste-like Recyclable Ga Liquid Metal Phase Change Composites Loaded with Miscible Ga2O3 Particles for Transient Cooling of Portable Electronics

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Experimental Investigation on Optimization of the Performance of Gallium-Based Liquid Metal with High Thermal Conductivity As Thermal Interface Material for Efficient Electronic Cooling

Sustainable Thermal Regulation of Electronics via Mitigated Supercooling of Porous Gallium-Based Phase Change Materials

Improving the thermal, mechanical, and insulating characteristics of thermal interface materials with liquid metal-based diphase structure

Gallium-indium nanoparticles as phase change material additives for tunable thermal fluids

Liquid metal phase change materials for thermal management of electronics

Micro-encapsulation of a low-melting-point alloy phase change material and its application in electronic thermal management

Ductile Cooling Phase Change Material

Convective Cooling of Compact Electronic Devices Via Liquid Metals with Low Melting Points

Gallium-Based Liquid Metal Amalgams: Transitional-State Metallic Mixtures (transm2ixes) with Enhanced and Tunable Electrical, Thermal, and Mechanical Properties

Transportable, Endurable, and Recoverable Liquid Metal Powders with Mechanical Sintering Conductivity for Flexible Electronics and Electromagnetic Interference Shielding

A graphene nanoflake-based flexible composite phase change material for enhanced heat dissipation in chip cooling

Combination of Heat Storage and Thermal Spreading for High Power Portable Electronics Cooling

Radiative Heat Transfer to Enhance the Performance of Liquid Metal-Based Phase Change Heat Sink under Natural Convection Condition

Thermal and Electrical Properties of Liquid Metal Gallium During Phase Transition

Thermally conductive composite phase change materials with excellent thermal management capability for electronic devices

Self-assembled Liquid Metal Nanoporous Film with Durability for Efficient Phase-Change Thermal Energy Management Via Surface and Interface Engineering

Design and Scalable Fabrication of Liquid Metal and Nano‐Sheet Graphene Hybrid Phase Change Materials for Thermal Management (Small Methods 9/2023)

Metallurgical Slag Modified Monolayer Graphene Hybrid SA-based Composite Phase Change Materials for High Thermal Conductivity

Advanced liquid metal cooling: Historical developments and research frontiers